Work Method; Battery Charge Level Controls; Dirty Surfaces; Indirect Scrubbing Or For Very Dirty Surfaces - CTM SWIFT EVO Manuel

is connected.
- Put the ignition key ( Photo C - 2) in and turn ON
the machine or switch on the machine pressing the
ON/OFF (Photo E - 2) and the SUCTION (Photo E -
4) buttons at the same time for at least 5 seconds.
- In the control panel, check the battery charge sta-
tus ( Photo C - 1 ) ( Photo E - 1 )
- Lower the squeegee unit by using the lift/lower
lever ( Photo D - 1 ) ( Photo G - 3 )
- Lower the brush plate unit by using the lift/lower
lever ( Photo D - 2 ) ( Photo G - 4 ).
- Switch ON the suction motor switch ( Photo C - 4
) ( Photo E - 4 ).
- Switch ON the brush motor switch ( Photo C - 3 )
( Photo E - 3 ); with the brush rotation is also acti-
vated the outflow of the detergent solution con-
trolled by the solenoid valve.
- Wash the floor moving forward slowly; turning off
the brush rotation switch the outflow of the clea-
ning solution stops.
To adjust the outflow of the cleaning solution
it is necessary to act on cap of the solution
water filter (Photo Q - 1); screwing the tran-
sparent cap increases the amount of flow,
while unscrewing the cap reduces the flow.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.
Model DC 24V with traction
- Verify that the battery connector placed in the
back of the machine ( Photo G - 1 ) is connected.
- Switch on the machine pressing the ON/OFF
(Photo F - 2) and the SUCTION (Photo F - 4) but-
tons at the same time for at least 5 seconds.
- In the control panel, check the battery charge sta-
tus ( Photo F - 1 )
- Lower the squeegee unit by using the lift/lower
lever ( Photo G - 3 ).
- Lower the brush plate unit by using the lift/lower
lever ( Photo G - 4 ).
- Switch ON the suction motor switch ( Photo F - 4).
- Switch ON the brush motor switch ( Photo F -3).
!
( ) The brush will start the rotation only
when the machine operator will operate the
brush operation lever ( Photo F - 5); with the
brush rotation is also activated the outflow
of the detergent solution controlled by the
solenoid valve.
- Wash the floor moving forward by pulling the trac-
tion lever ( Photo F - 5) or pushing the traction
lever to reverse traction; releasing the lever the
traction, brush rotation and detergent solution out-
flow will stop immediately.
To adjust the outflow of the cleaning solution
it is necessary to act on cap of the solution
water filter (Photo Q - 1); screwing the tran-
sparent cap increases the amount of flow,
while unscrewing the cap reduces the flow.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.

6.14 WORK METHOD

6.14.1 PREPARATION AND WARNINGS
Remove any loose solid residue from the surface to
be treated (using suitable tools, such as vacuum
cleaners, sweepers, etc.). It this is not done, the
solid dirt might prevent the squeegee from operat-
ing correctly, reducing drying efficiency.
Only trained personnel can drive this machine.

6.14.2 BATTERY CHARGE LEVEL CONTROLS

The sequence of lights of the battery charge control
( Photo C - 1 ) ( Photo E - 2 ) ( Photo F - 2 ) pro-
gressively turns off until the battery is discharged.
☞
( ) When the red light turns on it is neces-
sary to turn off the brush motor, close the
detergent solution outlet, finish drying the
small residual moisture and go to the battery
charging area to charge the battery.
!
( ) The batteries may be irreparably dam-
aged if the residual charge level drops too
low (see the battery operating manual). Do
not force the battery discharge beyond the
safety limits, turning the key off and on or in
any other manner.
6.14.3 DIRECT
SLIGHTLY DIRTY SURFACES
Scrubbing and drying in a single pass.
Prepare the machine as previously described and
use it as described in paragraph 6.13.
☞
( ) Never use the machine without the detergent
solution: the floor might be damaged.
6.14.4 INDIRECT SCRUBBING OR FOR VERY

DIRTY SURFACES

Scrubbing and drying in various passes.
Prepare the machine as previously described.
First set of operations:
Wash the floor as described in paragraph 6.13,
without drying the floor
Allow the detergent solution to work on the
dirty floor according to what is indicated in
the information relative to the detergent
used.
Second set of operations:
Proceed as explained in the previous "Direct Wash-
ing" paragraph (6.14.3) to also proceed with drying
36
SCRUBBING OR FOR