Structure And Functions - CTM SWIFT EVO Manuel

Check the battery charge level and charge, if nec-
essary.
Mount the brushes or scraper disks (with the abra-
sive disks) that are suitable for the surface and
work involved.
Mount the squeegee, check that it is solidly at-
tached and connected to the suction hose and that
the drying blades are not too worn.
Make sure that the recovery tank is empty. If not,
empty it completely.
Check and completely close the detergent solution
release control.
Fill the detergent solution tank with a mix of clean
water and non-foaming detergent in an adequate
concentration through the anterior hole. Leave 2
cm between the mouth of the plug and the level of
the liquid.
☞
( ) To avoid risks, become familiar with the ma-
chine movements, carrying out test runs on a large
surface without obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the following
simple but important operations:
- Identify the work area, moving all possible obsta-
cles out of the way; if the surface is very extensive,
work in contiguous and parallel rectangular areas.
- Choose a straight work trajectory and begin work-
ing from the farthest area to avoid passing over
areas that have already been cleaned.

6.2 STRUCTURE AND FUNCTIONS

PHOTO A Model E (AC 230V)
1 SUCTION MOTOR SWITCH
2 BRUSH MOTOR SWITCH
3 GENERAL ON/OFF SWITCH
PHOTO B Model E (AC 230V)
1 SQUEEGEE LIFT/LOWER LEVER
2 BRUSH PLATE LIFT/LOWER LEVER
3 RECOVERY TANK DRAIN HOSE
4 POWER SUPPLY CABLE
PHOTO C Model B (DC 24V)
1 BATTERY POWER TEST
2 GENERAL ON / OFF KEY SWITCH
3 BRUSH MOTOR SWITCH
4 SUCTION MOTOR SWITCH
PHOTO D Model B (DC 24V)
1 SQUEEGEE LIFT/LOWER LEVER
2 BRUSH PLATE LIFT/LOWER LEVER
3 RECOVERY TANK DRAIN HOSE
4 BRUSH MOTOR THERMAL BREAKER
5 BATTERY CONNECTOR
PHOTO E Model B (DC 24V)
1 BATTERY POWER TEST
2 GENERAL ON/OFF SWITCH
3 BRUSH MOTOR SWITCH
4 SUCTION MOTOR SWITCH
PHOTO F Model BT - (DC 24V with traction)
1 BATTERY POWER TEST
2 GENERAL ON/OFF SWITCH
3 BRUSH MOTOR SWITCH
4 SUCTION MOTOR SWITCH
5 FORWARD/REVERSE TRACTION OPERA-
TION LEVER
PHOTO G
Model B - BT - (DC 24V without and
with traction)
1 BATTERY CONNECTOR
2 BRUSH MOTOR THERMAL BREAKER
3 SQUEEGEE LIFT/LOWER LEVER
4 BRUSH PLATE LIFT/LOWER LEVER
5 RECOVERY TANK DRAIN HOSE
6 BATTERY CHARGER POWER SUPPLY
CABLE
7 BUILT-ON BATTERY CHARGER
PHOTO H
Model B - BT - (DC 24V without and
with traction)
1 BATTERY CHARGER COVER
2 RED LED - BATTERY DISCHARGED
3 GREEN LED - FULL BATTERY CHARGE
4 DIP-SWITCHES
5 PLASTIC CAP
6 DIP-SWITCH NR. 1 FOR PB-ACID/GEL
BATTERY SETTING
PHOTO I
Model B - BT - (DC 24V without and
with traction)
1 OPENING CLIP SPRING
2 BATTERY COMPARTMENT WITH 12V
BATTERIES
3 BATTERY CONNECTION WIRING
PHOTO L
Model B - BT - (DC 24V without and
with traction)
BATTERY CONNECTION DIAGRAM
PHOTO M Model E - B - BT
1 SQUEEGEE BUMPER WHEEL
2 SQUEEGEE PRESSION ADJUSTING KNOB
3 SUCTION HOSE
4 SQUEEGEE BLADES REPLACEMENT
KNOB
5 SQUEEGEE WHEEL
6 SQUEEGEE FIXING KNOB
7 SQUEEGEE INCLINATION ADJUSTING
KNOB
32