Campbell Hausfeld CHN10450 Instructions D'utilisation page 5

Operating the Tool
(Continued)
1. Disconnect the
air supply from
the tool to add
lubricant.
2. Turn the tool so
the air inlet is facing
up. Place 4-5 drops of
30 W non-detergent
oil into air inlet. Do
not use detergent
oils, oil additives, or
air tool oils. Air tool oils contain
solvents which will damage the
tool's internal components.
3. After adding oil, run
tool briefly. Wipe off
any excess oil from
the cap exhaust.
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the tool.
1. The air
compressor
must be able
to maintain a
minimum of
60 psi when the tool is being used.
An inadequate air supply can cause
a loss of power and inconsistent
driving.
2. An oiler can be
used to provide oil
circulation through
the tool. A filter can
be used to remove
liquid and solid
impurities which can rust or "gum
up" internal parts of the tool.
3. Use 1/4 in. air 150 psi WP
hoses with
a minimum
working
pressure of 150
psi. Use 3/8 in. air hoses for 50 ft. run
or longer. For better performance,
install a 3/8 in. quick plug (1/4 in.
NPT threads) with an inside diameter
of .315 in. (8mm) on the tool and a
3/8 in. quick coupler on the air hose.
4. Use a pressure
regulator on
the compressor,
with an
operating
pressure of 0 -125 psi. A pressure
regulator is required to control
the operating pressure of the tool
between 60 and 100 psi.
SINGlE SEqUENTIal MODE
This mode requires
the trigger to be
pulled each time a
fastener is driven.
The tool can be
actuated by depressing the WCE against
the work surface followed by pulling
the trigger.
The trigger must be released to reset
the tool before another fastener can be
driven.
CHECKING THE WORK CONTaCT
ElEMENT (WCE)
60 psi
Element (WCE) trip mechanism before
min.
each use. The WCE must move freely
without binding through its entire
100 psi
travel distance. The WCE spring must
max.
return the WCE to its fully extended
position after being depressed. Do
not operate the tool if the WCE trip
mechanism is not operating properly.
Personal injury may occur.
1. Disconnect the
air supply from
the tool.
2. Remove all
fasteners from
the magazine
(see Loading/
Unloading).
3. Make sure the trigger
and work contact
element (WCE) move
1/4 inch I.D.
freely up and down
without sticking or
binding.
4. Reconnect air
supply to the
tool.
5. Depress the Work
6. Remove the tool from
7. Pull the trigger
Check the operation
of the Work Contact
8. Depress the
must not be used. Do not actuate the
tool unless the tool is placed firmly
against the work piece.
lOaDING/UNlOaDING THE TOOl
1. Always disconnect the tool from
2. Push down
Movement
3a. For nails, insert
5
CHN10450
Contact Element
(WCE) against the
work surface without
pulling the trigger.
The tool MUST NOT
OPERaTE. Do not use the tool if it
operates without pulling the trigger.
Personal injury may result.
the work surface.
The Work Contact
Element (WCE) must
return to its original
down position.
The tool MUST NOT OPERaTE.
Do not use the tool if it operates
while lifted from the work surface.
Personal injury may result.
and depress the
work contact
element (WCE)
against the
work surface. The tool MUST NOT
OPERaTE.
Work Contact
Element (WCE)
against the
1
work surface.
Pull the trigger. The tool MUST
OPERaTE.
An improperly
functioning tool
the air supply before loading
fasteners.
on the latch
button. Pull
back on the
magazine cover.
a stick into
the magazine.
Make sure the
pointed ends
of the fasteners
are resting on the bottom ledge
www.chpower.com
2
Latch
button