Maintenance - Campbell Hausfeld CHN10450 Instructions D'utilisation

Operating Instructions
Operating the Tool
(Continued)
of the magazine when loading.
Make sure the nails are not dirty or
damaged.
3b. For staples, load
a clip of staples
with the crowns
straddling the
magazine rail.
4. Push the
magazine cover
forward until
latch button
pops up.
5. Always unload all fasteners before
removing tool from service.
Unloading is the reverse of loading,
except that you must disconnect
the air supply before unloading.
aDJUSTING THE FaSTENER
PENETRaTION
The tool is equipped with an adjustable
depth of drive feature. This allows the
user to determine how deep a fastener
will be driven into the work surface.
1. Adjust operating pressure so
fasteners are driven consistently. Do
not exceed 100 psi.
2. For shallow
penetration,
(C)
turn the
wheel (C)
to right to
the extent
desired.
3. For deeper
penetration,
turn the wheel (C) to left to the
extent desired.
4. Make sure trigger
and work contact
element (WCE) move
freely up and down
without binding or
sticking after each
adjustment.
www.chpower.com
aDJUSTING THE DIRECTION OF THE
EXHaUST
The tool is
equipped with
an adjustable
direction exhaust
deflector. This is
intended to allow
the user to change the direction of the
exhaust. Simply twist the deflector to
Magazine
rail
any direction desired.
ClEaRING a JaM FROM THE TOOl
1. Disconnect the
air supply from
the nailer.
2. Remove all
nails from
the magazine
(see "Loading/
Unloading The
Nailer").
cause the fasteners to eject from the
front of the tool.
3. Undo latch by
pulling out
and down. The
wire latch will
disengage from
the hooks on the nose.
4. The door can
now be rotated,
exposing
the jammed
fastener.
5. Remove the
jammed
fastener, using
pliers or a
screwdriver if
required.
6 Rotate door
back into the
Movement
closed position.
7. Extend the wire
latch and place
over the hooks
on the nose.
8. Close the latch
by pushing the
9. Make sure the
Rotate

Maintenance

TECHNICal SERvICE
Please call our Tool Hotline at 1-800-
543-6400 with any questions regarding
the operation or repair of this tool or
for additional copies of this manual.
FaSTENER aND REPlaCEMENT
PaRTS
18 gauge fasteners (or equivalent - see
Fastener Interchange Information).
Failure to remove
Use only genuine Campbell Hausfeld
all fasteners will
replacement parts. Never substitute
parts. Do not use modified parts or
parts which will not give equivalent
performance to the original equipment.
Tool performance, safety and durability
could be reduced. When ordering
replacement parts or fasteners, specify
by part number.
TOOl REPaIR
Only qualified personnel should repair
the tool, and they should use genuine
Campbell Hausfeld replacement parts
and accessories, or parts and accessories
which perform equivalently.
aSSEMblY PROCEDURE FOR SEalS
When repairing a tool, the internal
parts must be cleaned and lubricated.
Parker O-lube or equivalent must be
used on all o-rings. Each o-ring must be
coated with O-lube before assembling.
A small amount of oil must be used on
all moving surfaces and pivots. After
reassembling, a few drops of 30W
non-detergent oil or equivalent, must
be added through the air line before
testing.
STORaGE
The tool should be stored in a cool, dry
place.
6
latch up and in until the latch snaps
into place.
trigger and
work contact
element (WCE)
move freely
up and down without sticking or
binding.
Use only genuine
Campbell Hausfeld