Télécharger Imprimer la page

Publicité

Liens rapides

IP Serial Server 1 Port for DIN Rail
User Manual
Benutzerhandbuch
Manuel d'utilisateur
Manuale
LINDY No. 42721
www.lindy.com
Tested to Comply with FCC Standards
For Home and Office Use!
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH
Introduction
Thank you for purchasing the LINDY IP serial Server for DIN Rail
Mounting. It allows connection of a RS232 serial device to
10/100 Ethernet, thus controlling a RS232 device or reading out
data from a measuring instrument with RS232 port via internet or
an in-house network.
Main Features
Mode: Asynchronous serial communication
Connectors: 1x D9 M, 1x RJ-45 F (10/100 Mbit/s)
10/100 Mbit/s, auto MDI/MDIX
Configurable via web browser
Full and half duplex serial port modes
Baud rate up to 921.6 Kbit/s
For DIN Rail mounting
Includes 12V 1.25A MC PSU w/1.4m DC cable and DC
adapter cable (5.5/2.5mm to 3.5/1.35mm)
2-pin terminal block, supports 10-30V power input
Power consumption: 90mA@24VDC
Supported Operating Systems: Windows 2000/XP/Ser-
ver 2003/Vista/Server 2008/Windows 7 (64-bit)/8 & 8.1
Package Contents
IP Serial Server
Mounting Bracket
Multi-Country PSU 12V 1.25A w/ DC adapter cable
Generic CD
LINDY Manual
English
Deutsch
Français
Italiano
-
SECOND EDITION
(NOV 2014)
English
English
English
Technical Specification
Gateway, IP address
Operation mode: VSP COM (Virtual Serial Port), TCP
Server, TCP Client, UDP, Paired Mode
Signals: TXD, RXD, RTS, CTS, DTR, DSR, DCD, GND
Remote Control of RTS, CTS, DTR and DSR lines
Internal EEPROM for configuration storage
Detailed status indication via LEDs
Setup through the serial port or network
HTTP, UDP (management configurable) tools setup
"On the fly" commands for intermediate serial port
configuration change
Serial side modem commands for network connections
control
Direct control of ADSL modems
Data Bits: 7, 8 - Stop Bits: 1,2
Flow Control: RTS/CTS, X-On/X-Off
Parity: None, Even, Odd, Space, Mark
Supports HTTP, DHCP, ICMP (PING), Static IP and ARP
1024KB flash for firmware, aplication and data storage
2KB EEPROM for data storage
15 kV ESD protection for RS-232 serial port
Operating Temperature: -35°C ~ 70°C
Humidity: 5-95%, non-condensing
The Virtual Serial Port Drivers for Windows allow you to
transparently access your device server´s serial port as if it was a
real COM port of your PC.
This serial over IP device supports standard TCP/IP and UDP/IP
protocols. Open a socket and exchange data with the serial port of
your device server directly.
English

Publicité

loading

Sommaire des Matières pour Lindy 42721

  • Page 1 Introduction English Technical Specification English • Thank you for purchasing the LINDY IP serial Server for DIN Rail Gateway, IP address • Mounting. It allows connection of a RS232 serial device to Operation mode: VSP COM (Virtual Serial Port), TCP...
  • Page 2 • Installation Data English Gateway address: 192.168.1.254 • Subnet mask: 255.255.255.0 Set up steps – Software: On the driver CD go to the directory 'RS232 Device Server'. According to your Windows version (32 or 64 Bit), open up the respective subdirectory ('Serial Device Server -<OS suffix>', where 'OS suffix' means 'x86' for a 32Bit Windows and 'amd64' for a 64Bit Windows).
  • Page 3 POWER ON Serial Over IP Device RUN Atil VSP Manager Virtual Serial Ports setting Select Open Virtual Serial COM Click Add...
  • Page 4 Click blue icon and Settings Change IP address Search Serial over IP Devices Different Local Area Network Click Refresh Change IP address Local Area Click OK Reboot Serial Over IP Device...
  • Page 5 Local Area Network Status and Click Settings Click Ch1 For RS232 RS422 Baud rate setting Serial Over IP Device Power ON Initial Baud rate the same equipment Baud rate setting Serial Over IP Device Power ON Initial Baud rate the same equipment TCP/IP (Winsock) TCP/IP (Winsock)
  • Page 6 RS422 SW set RS485 Baud rate setting Serial Over IP Device Power ON Initial Baud rate the same equipment TCP/IP (Winsock) RS485 SW set Red block set and Click OK Click Select...
  • Page 7 Virtual Serial Port (Virtual COM Port ) OK Open COM20 Delete Virtual Serial Port select COM20 and Click Remove Checking Virtual Serial Port Control Panel Click System Click Control Panel...
  • Page 8 Click Ports Click Hardware and Device Manger Test COM Port Loop back Loop back DB9 Serial over IP Virtual Serial Port OK...
  • Page 9 Open Hyper Terminal Name aa Connect Using COM20 and Click OK...
  • Page 10 TCP/IP Link Check set Ch Transport protocol Virtual Serial Port COM20 test OK IP-address: 192.6.1.200 Select Serial interface RS232 RS422 RS485 Default Port number :1001 Baudrate set Ch1=1001,Ch2=1002,Ch3=1003,Ch4=100...
  • Page 11 Virtual Serial Port Driver Windows 7 ATILDST-5-09-02-amd64 for 64bit windows operation system ATILDST-5-09-02-x86 for 32bit windows operation system...
  • Page 12 RUN Atil VSP Manager Add Virtual Serial Ports Settings Select Click Browse for DS...
  • Page 13 Baud rate setting Serial Over IP Device Power ON Initial Baud rate the same equipment Change IP address Local Area Click OK TCP/IP (Winsock) Reboot Serial Over IP Device Select VSP name COMx IP-address :port...
  • Page 14 Test COM Port Loop back Virtual Serial Port OPEN COM20 OK Virtual Serial Port Driver Windows 8.x ATILDST-5-09-02-amd64 for 64bit windows operation system ATILDST-5-09-02-x86 for 32bit windows operation system...
  • Page 15 RUN Atil VSP Manager Add Virtual Serial Ports Settings Select Click Browse for DS...
  • Page 16 Baud rate setting Serial Over IP Device Power ON Change IP address Local Area Click OK Initial Baud rate the same equipment Reboot Serial Over IP Device TCP/IP (Winsock) Select VSP name COMx IP-address: port...
  • Page 17 Test COM Port Loop back Virtual Serial Port OPEN COM20 OK WEB setting Initial factory setting Password : IP-address:192.168.1.1 Gateway-address :192.168.1.254 Example IP 192.6.1.14 Local Area Network IP-address xxx.xxx.xxx.xxx configuration OK Save...
  • Page 18 Serial Setting For Atil VSP Manager and TCP/IP (Winsock) Power ON Initial Baud rate TCP/IP (Winsock) baud Routing Status Initial factory setting Password : IP-address:192.168.1.1 Gateway-address :192.168.1.254...
  • Page 19 Einführung Deutsch Vielen Dank für den Kauf des LINDY IP Serial Servers mit dem Sie ein beliebiges RS232-Gerät an ein 10/100 Netzwerk anschliessen können. Er ermöglicht die Steuerung eines seriellen RS232- Gerätes oder das Auslesen von Daten eines Messgerätes über das Internet oder ein hausinternes Netzwerk.
  • Page 20 Introduction Français Specifications Techniques Français • Merci d’avoir choisi le serveur IP pour rail DIN LINDY. Il permet Passerelle, adresse IP • la connexion de périphérique RS232 série au réseau Ethernet Mode de fonctionnement: VSP COM (Virtual Serial Port), 10/100, permettant ainsi de contrôler un périphérique RS232 ou TCP Server, TCP Client, UDP, Paired Mode •...
  • Page 21 Après finalisation de l’installation, du menu démarrer ou Introduzione Italiano metro, le logiciel "Atil VSP Manager" pourra être lancer. Grazie per aver acquistato il LINDY IP Serial Server su Guide DIN. Configuration via réseau Questo dispositivo permette di connettere apparati seriali RS232 •...
  • Page 22 Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato. se fosse una porta COM reale del vostro PC Questo dispositivo supporta i protocolli di rete standard TCP/IP e LINDY No. 42721 UDP/IP. E’ possibile aprire un socket e scambiare dati www.lindy.com direttamente con il vostro server seriale.