Gas, Dust, Steam, Smoke; Noise; 2.10 Illumination; Oils, Greases And Other Chemical Substances - GÖLZ FS175 Mode D'emploi Et Liste Des Pièces De Rechange

FS175
Protective installations with fault-current protection
units used in non-stationary equipment must be
checked for correct operation at least once a month by
a properly instructed person.
Fault-current and fault-voltage protection units must be
checked for correct operation by actuating the testing
facility:
once on every working day in the case of mobile
•
equipment,
at least once every six months in the case of
•
stationary equipment.
2.8

Gas, dust, steam, smoke

Operate combustion engines only in well-ventilated
rooms! Before starting the unit in closed rooms, make
sure that the room is sufficiently ventilated and use the
exhaust gas hose!
Welding, burning and grinding operations on the
machine are only to be carried out if this is explicitly
authorized (there is the danger of fire and explosion)!
Before welding, burning and grinding operations clean
the machine and its surrounding area from dust and
flammable substances
ventilation (danger of explosion)!
When working in confined spaces observe any existing
national regulations!
2.9

Noise

During operation sound protection devices on the
machine must be in safe position. Wear the prescribed
personal ear protection! (UVV 29 § 10, Article 29 of
the Accident Prevention regulations).
The use of noise emitting machines may be restricted
to certain times by national or local regulations.

2.10 Illumination

The machine is designed for use in daylight! The
machine operator / owner must ensure sufficient
workplace lighting for non-illuminated work sites!
2.11 Oils, greases and other chemical
substances
When handling hydraulic fluids, lubricants, greases or
preservatives (referred to hereinafter as fuels and
lubricants), the safety regulations which apply to the
respective machine are to be observed!
Avoid long contact of the fuels and lubricants with your
skin! Careful cleaning of the skin from adhering fuels
and lubricants is necessary.
and care for sufficient
Be careful when handling hot consumables (risk of
burning or scalding) particularly at liquid temperatures
above 60° C, avoid any skin contact with these liquids!
If you get fuels or lubricants in your eyes, rinse them
immediately and carefully with potable water. Then
consult a doctor.
Remove flown out fuels and lubricants immediately!
Therefore use a binder.
Fuels and lubricants must not seep into the soil or into
the public sewage system! Fuels and lubricants which
can no longer be used are to be collected, properly
stored and to be properly disposed of.
The respective regulations and laws for handling fuels
and lubricants which are valid in the country of use are
to be observed and adhered to. This also applies to
the disposal of such fuels and lubricants. To inform
yourself turn to the responsible authorities.

2.12 Transport

Use only suitable means of transport and lifting gear of
sufficient capacity when loading or transporting the
machine! Appoint an experienced instructor for the
lifting operation!
Always observe the instructions given in the operating
manual when lifting the machine (use only the
prescribed lifting eyes for attaching the lifting gear)!
Use only suitable transport vehicles with sufficient load
capacity! Secure the load carefully. Use suitable
fastening points for securing!
Before loading the machine or parts of it, secure the
machine against inadvertent movement! Attach a
suitable warning sign!
The blade must be removed for transport. Even in
case of a minor change of location, the engine must be
stopped!
Before using the machine again, make sure that such
protection material or devices are properly removed!
Parts which had to be removed for transporting of the
machine must be refitted and secured carefully before
the machine is used again!
Before setting the machine in motion always check
that all accessories are safely stowed.
The recommissioning procedure must be strictly in
accordance with the operating instruction! Observe the
instructions given in the operating instruction when
reassembling and operating the machine.
- 28-
®
Lifting eye
5007287-01
BA-DE-GB-FR-NL