Light Therapy Mode; Using Sonic Cleansing Brush; Treatment Tips; Ultrasonic Therapy Mode - QLARITE LEDSONIC+ Manuel D'utilisation

• Step 5: Long touch " " for power off when finished treatment.
• Step 6: Use a dry soft cloth to clean the surface of the attachment.
• Step 7: The appliance will switch off after 15 min.
Note: 10 min. is the recommended treatment time per session. The appliance will
automatically power off after 15 min.
B) Light Therapy Mode
Caution: Protect your eyes from red light.
If you have to treat areas around the eyes with blue or red attachment, use the
silicon protector provided with the device. Always keep away from eyes by at
least 1cm.
• Step 1: Red LED attachment is correctly placed on the attachment connector
base.
• Step 2: Long touch " " for power on.
• Step 3: Touch "SELECT" for light on.
• Step 4: Long touch " " for power off after completing treatment.
• Step 5: Use a dry soft cloth to clean the surface of the attachment.
• Step 6: LEDSONIC+ will "beep" for each minute during treatment time.
• Step 7: LEDSONIC+ will power off after 9 min.
Note: The appliance will automatically power off after 9 min. Please wait 8 min. for cool
down before powering on again.
C) Using sonic cleansing brush
Caution: Never use cleaning products containing alcohol, petrol or acetone
as they may irritate the skin.
• Step 1: Ensure sonic cleansing brush attachment is correctly attached on the
connector base.
• Step 2: Remove all makeup, dampen face with water and apply your regular
cleansing product onto the brush attachment.
• Step 3: Dampen face with water and apply cleansing lotion onto brush. Switch
on device.
• Step 4: Long touch " " for power on.
• Step 5: Touch "SELECT" to start
• Step 6: Start cleansing at your chin with gentle upward strokes along your jaw
to your ear, moving gradually higher to cleanse the whole cheek.
• Step 7: Change to the other side of your face and forehead by working in
circular motion. Lastly, cleanse both sides of the nose by gently gliding the
brush head up and down.
• Step 8: Detach the sonic cleansing brush head to wash the brush surfaces with
clean water and soap. Pat dry with a lint-free cloth or towel.
Note: 1~2 mins. is the recommended cleansing routine. The appliance will "beep" for each
minute during cleansing mode.
6.2

Treatment Tips

A) Ultrasonic Therapy Mode
• Apply the skin care products (serum/lotion) on the ultrasonic attachment
surface (See Fig. 9) and choose frequency according to treatment area (See
Fig 2).
Fig. 9
• Maximizing the effects of your skin care products – Ultrasonic waves are
effective for product penetration with specific frequencies for different areas:
A) Use with products like cream, serums or lotion: Repeat each step a total of
5 times: glide LEDSONIC+ very slowly with a slight pressure. (See Fig. 10)
B) Use with products like facial mask: Repeat each step a total of 10 times: glide
LEDSONIC+ very slowly with slight pressure. (See Fig. 10)
B) Light Therapy Mode
LEDSONIC+ uses a super-luminous LED array to deliver concentrated beams
of light for phototherapy effect. This safe, painless, natural healing process
converts light energy within skin cells, very similar to the way photosynethesis
takes sunlight and turns it into food energy in plants. To maximize the effect,
we highly recommend:
• For acne treatment: Use the Blue LED light therapy (Blue LED head is sold
separately) for 3 minutes over affected areas twice daily. To maximize the
results, follow with the red LED light therapy for 3 minutes over affected
areas twice daily.
• Skin rejuvenation and firming: Use the red LED light therapy, holding
the appliance for 3 minutes on different areas of the face (see section
4.2.2"Areas not to treat"), then move to another area of the face. The
appliance will "Beep" to remind you of every minute of treatment.
5 MHz
Fig. 10
1 MHz