Polygroup RX Série Notice De Montage Et D'utilisation page 2

1.0
SAFETY INSTRUCTIONS: EXTREMELY IMPORTANT!
Read and observe all instructions. Keep this manual for future reference.
WARNING! Follow the manufacturer's instructions and correctly assemble the pool set before starting the filtration. This product is not intended for use in
water. Verify the pool is installed on a level and firm surface free of debris and sharp objects.
WARNING! The installation requires and adult.
WARNING! Prior to commissioning the pool, check all hoses and accessories for correct installation and reliable connection. The packaging materials are not
toys. After installation, remove all packaging loops/cords from the reach of children.
WARNING! Do not bury the power cables into the ground. Place the cables to prevent damage by lawn mowers, hedge cutters or other equipment, which
could damage it.
WARNING! This pump is designed for temporary surface pools, not for fixed built-in pools. Do not operate the filtration pump without water. The pump is
not self-priming and therefore it must be placed to allow its natural flooding with water. Incorrect use may lead to a damage of the product.
WARNING! Never allow swimming underwater and diving into the pool or on its edge. If you disregard this rule, it may lead to serious injury, paralysis or death.
WARNING! Prevent children from use of the filtration pump without a supervision of an adult.
WARNING! It is intended for use under the supervision of an adult. Never leave children unattended near water. Unsuitable for children up to 36 months of
age, because small parts could cause suffocation.
WARNING! To avoid the risk of electric shock, immediately after identifying any damage of the cable, arrange its repair by a qualified electrician.
WARNING! The power cable of this pump cannot be replaced. It the cable is damaged and cannot be repaired, the pump must be disposed of.
WARNING! To prevent the electric shock, connect the filtration pump to an outlet of the power supply circuit complying with ČSN with current protector
(RCD) with breaking current up to 30mA. If you are not sure, call a qualified electrician to install the protector. The filtration pump contains electrical parts
and as such in must be installed was far from the pool as possible. The power outlet for the pump connection must be located at least 3.5m from the pool
wall. Use correctly installed and grounded outlet.
WARNING! The equipment is not designed for the use by persons (including children) with reduced physical, sensory or mental capacities, unless a supervi-
sion and training by a qualified person is provided; persons not familiar with the operation in the scope of this manual; persons under the influence of drugs,
intoxicating substances etc., reducing the capability of quick reaction.
WARNING! To reduce the risk of injury, the pool may be used only under a supervision of an adult. Do not allow anyone to use the pool while alone, without
supervision.
WARNING! The filtration pump may not be operated if the pool is occupied by swimmers.
WARNING! The filtration system may be used for any period of time, but NEVER when the pool is occupied.
WARNING! Contamination with grease, used during the assembly of the pool, may appear on the surface of the pool.
2.0
INSTRUCTIONS FOR RX PUMP INSTALLATION
1. Remove all parts of the filtration pump from the box.
2. First remove the top threaded ring (5), top filtration cover (4) and the filtration insert (10) from the filtration assembly. Lubricate the O-ring (20) on the
pump spiral cover with grease. Hold the filtration case (3) carefully and insert the pump body (1) so the inlet hole from the spiral cover reaches the hole
on the side of the base. Insert the pump so it rests on the bottom and the two lugs on the spiral cover fit into two slots in the bottom of the filtration
case (3). Reach inside the filtration case and fit the pump's nut (2) on the inlet hole of the spiral cover. Turn the nut (2) clockwise to tighten it. See Fig. 2.
3. Take the inlet and discharge hoses (7, 8) and the four hose couplings (9) from the bag with the accessories. Loosen the hose clamps and insert them on both
ends of each hose. Fit one hose on the filtration case inlet and one hose to its discharge. Tighten both hose clamps (9) on the filtration case. See fig. 1, 3 and 4.
4. Install the strainer with grommet (11, 12) to the pool wall outlet. Fit the inlet hose from the filtration case to the pool grommet. Tighten the hose coupling.
See fig. 1, 3 and 4.
5. Install the baffle with grommet (11, 13) to the pool wall outlet. Fit the inlet hose of the filtration case to the inlet pool grommet. Tighten the hose coupling.
Start filling the pool. See fig. 1, 3 and 4.
6. Once the pool is full, place the filtration between these two connections on the side of the pool, app. 15cm from the ground. Inlet water hose (7), coming
into the filtration case from the top, should lead to the filtration from the right, and the return hose (8), coming from the pump (in the casing's bottom),
should lead to the left. See Fig. 3. You can fix the filtration position on the grass using the supplied steel pins.
7. Unscrew the vent bolt (6) on the filtration cover (4) by app. one and half turn. NOTE: THE SYSTEM MUST BE VENTED DUE TO AIR LEAKS DURING THE FILLING
OF THE FILTRATION WITH WATER.
8. When the system is full, water should start to leak through the groove in the venting bolt. Manually tighten the bolt in the filtration cover, until the O-ring
seals the bolt and water stops flowing out.
9. At this point the filtration should be prepared for operation. Check all hoses and connections as well as the venting bolt for water leaks.
10. Fill more water into the pool if needed.
EN