Vetus WTKIT Instructions D'installation Et Mode D'emploi Destiné Au Propriétaire page 9

2 3 Connecting the tank
Connect up the tank with good quality reinforced hose. Avoid sharp
bends or kinks in the hose.
The reinforced hose must be of quality suitable for drinking water
and resistant to a temperature of at least 60 degrees C and a pressure
of 400 kPa (4 bar, 58 psi).
Vetus supplies a hose suitable for tap water. It is tasteless, non-poi-
sonous, resistant to temperatures from -5 to +65 degrees C (+23 to
+149 degrees F) and has a working pressure of 1500 kPa (15 bar) 16
mm. dia. (215 psi - 5∕8" dia.) and 800 kPa (8 bar) - 38 mm. dia. (116
psi - 11∕2")
Article Code:
DWHOSE16A, drinking water hose, 16 mm (5∕8") internal diameter, and
DWHOSE38A, drinking water hose, 38 mm (11∕2") internal diameter.
Fit each hose connection with a good hose clamp.
Fit filler cap A
Install a filler hose B, 38 mm (11∕2") internal diameter, between the
filler cap and the tank. Instal this hose in such a way that neither tank
nor filler cap are subject to mechanical loads.
Fit air-relief nipple C as high as possible above the level of the top
of the tank. Ensure that the air-relief nipple is fitted where it cannot
fill with rain or other water and at least 30 cm above the waterline.
Fit air-relief pipe D, 16 mm (5∕8") internal diameter, between air-
relief nipple and the tank.
When viewed from the tank, the air-relief pipe should be fitted
straight up.
Fit the tap water supply pipe E, 16 mm (5∕8") internal diameter, be-
tween tank and pump. A non-priming pump should be lower than, or
at the same height as the underside of the tank. A self-priming pump
can be mounted at any height in relation to the tank.
Connect 2 tanks together using T-pieces in the water supply pipes
and if required air-relief pipe.
2 4 Check
Check the system for any leaks. Extraction pressure 20 kPa (0.2 bar)
(4.4 psi).
Sticker
Apply the blue 'Fresh water tank' sticker on the tank, the text must be
readable after installation of the tank and also affix the content sticker.
Connection kit for drinking water tanks
A
C
B D
4
1
2
3
E
A
C
D
B
1
5
2
3
4
1 Inspection cover
2 Filler connector
3 Supply connector
4 Air-relief connector
5 T-piece connection
Fresh water tank
• Tank capacity of:
• P max. 30 kPa (0.3 bar | 4.35 psi) • Meets KTW standard • Drinking water safe
Quality product by vetus , Schiedam Excellent Worldwide
warranty network
Designed and made in the Netherlands
AT147583W.VE
Waste water tank
• Tank capacity of:
• P max. 30 kPa (0.3 bar | 4.35 psi) • According to ISO 8099 • 0613
vetus
Quality product by , Schiedam Excellent Worldwide
Designed and made in the Netherlands warranty network
AT147583B.VE
xx litres
Diesel fuel tank
xx.x Imp.Gal. | xx.x US Gal.
xx litres
xx.x Imp.Gal. | xx.x US Gal.
• Tank capacity of:
xx litres
• Max. 100 °C
• Max. ll-up height 3.5 m
xx.x Imp.Gal. | xx.x US Gal.
• Max. test pressure 30 kPa (0.3 bar | 4.35 psi) • According to ISO 21487
• 0613 xx litres
xx.x Imp.Gal. | xx.x US Gal.
Quality product by vetus , Schiedam Excellent Worldwide
xx litres
Designed and made in the Netherlands warranty network
AT147583F.VE
xx.x | xx.x
Imp.Gal. US Gal.
42 litres 61 litres 88 litres 110 litres 137 litres
9.2 Imp.Gal. | 11.1 US Gal. 13.4 Imp.Gal. | 16.1 US Gal. 19.4 Imp.Gal. | 23.2 US Gal. 24.2 Imp.Gal. | 29 US Gal. 30.1 Imp.Gal. | 36.2 US Gal.
170 litres 215 litres 335 litres 390 litres
AT147583A.VE
37.4 | 44.9 47.3 | 56.8 73.7 | 88.5 85.8 | 103
Imp.Gal. US Gal. Imp.Gal. US Gal. Imp.Gal. US Gal. Imp.Gal. US Gal.
ENGLISH
min. 40 cm
(16")
F
F
E
1
4
3
A Filler cap
B Filler hose
C Air-relief nipple
D Air-relief pipe
E Tap water pipe
F Water pump
Fresh water tank
xx litres
• Tank capacity of:
xx.x | xx.x
Imp.Gal. US Gal.
• P max. 30 kPa (0.3 bar | 4.35 psi) • Meets KTW standard • Drinking water safe
vetus Excellent Worldwide
Quality product by , Schiedam
Designed and made in the Netherlands warranty network
AT147583W.VE
9
050101.06