Declaration Of Conformity; Dust/Chip Extraction; Starting Operation - BTI A-BS 12 V Notice Originale

OBJ_BUCH-3429-001.book Page 29 Friday, December 15, 2017 4:05 PM

Declaration of Conformity

We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with all relevant provisions of the direc-
tives 2011/65/EU, 2014/30/EU, 2006/42/EC
including their amendments and complies with the
following standards:
EN 60745-1:2009+A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
EN 62471:2008
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 50581:2012.
Technical documents at:
BTI Befestigungstechnik GmbH & Co. KG
74653 Ingelfingen
GERMANY
ppa. Stephan Uder Martin Mayer-Hagelstein
Head of Procurement Director Marketing &
Department E-Commerce
BTI Befestigungstechnik GmbH & Co. KG,
Salzstraße 51, 74653 Ingelfingen, GERMANY
Ingelfingen, 01.12.2017
Assembly
Battery Charging (see figure A)
Note: The battery supplied is partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before us-
ing your power tool for the first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging by the "Electronic Cell Protection
(ECP)". When the battery is empty, the machine is
switched off by means of a protective circuit: The
inserted tool no longer rotates.
 Do not continue to press the On/Off switch af-
ter the machine has been automatically
switched off. The battery can be damaged.
To remove the battery 5 press the unlocking but-
tons 4 and pull out the battery downwards. Do not
exert any force.
Observe the notes for disposal.
1 609 92A 497 • 15.12.17
Changing the Tool (see figure B)
 Before any work on the machine itself (e. g.
maintenance, tool change, etc.) as well as dur-
ing transport and storage, remove the battery
from the power tool. There is danger of injury
when unintentionally actuating the On/Off
switch.
The drill spindle is locked when the On/Off switch
7 is not pressed. This makes quick, convenient and
easy changing of the tool in the drill chuck possi-
ble.
Open the keyless chuck 1 by turning in rotation di-
rection , until the tool can be inserted. Insert the
tool.
Firmly tighten the collar of the keyless chuck 1 by
hand in rotation direction .

Dust/Chip Extraction

 Dust from materials such as lead-containing
coatings, some wood types, minerals and metal
can be harmful to one's health. Touching or
breathing-in the dust can cause allergic reac-
tions and/or lead to respiratory infections of the
user or bystanders.
Certain dust, such as oak or beech dust, is con-
sidered carcinogenic, especially in connection
with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may
only be worked by specialists.
– Provide for good ventilation of the working
place.
– It is recommended to wear a P2 filter-class res-
pirator.
Observe the relevant regulations in your country for
the materials to be worked.
 Prevent dust accumulation at the workplace.
Dust can easily ignite.
Operation

Starting Operation

Inserting the battery
Note: Use of batteries not suitable for the machine
can lead to malfunctions of or cause damage to the
power tool.
Set the rotational direction switch 6 to the centre
position in order to avoid unintentional starting. In-
sert the charged battery 5 into the handle so that it
can be felt to engage and faces flush against the
handle.
English | 29