Niko 410-00352 Manuel D'utilisation page 4

410-00352
5 Start programming the position. If necessary,
correct the position of the roller shutter/blind
with a programmed transmitter
6 Current position of the roller shutter/blind is
saved. When all the LEDs go out, the receiver is
ready for operation again
4.5. Deleting the transmitter
In delete mode, individual transmitters can be deleted from the memory of an output.
Note: If the transmitter is programmed in several outputs, it must be deleted individually from each output as
necessary. If an attempt is made to delete a transmitter that is not programmed into the selected output, the
LEDs flash quickly and the receiver remains in delete mode.
Step Operation
1 Start the programming mode in 3- or 2-button
mode
2 Select delete mode L
3 Select output. Only one output can be selected.
Output can be changed as often as required
4 Start delete mode
5 Delete transmitter from the selected output
4.6. Deleting all transmission codes (Reset)
All programmed transmitters are deleted and all switching times for the respective output are reset. A reset must
be performed individually for each output.
Step Operation
1 Start the programming mode in 3- or 2-button
mode
2 Select delete mode L
3 Select output. Only one output can be selected.
Output can be changed as often as required
4 Start delete mode
5 Delete all transmitters from the selected output
and reset all times to the factory default settings
5. SPECIFICATIONS
Frequency 868.30 MHz
Modulation FSK
Protocol Easywave
Power supply 230 V AC 50 Hz
Output 2 potential-loaded outputs each with 2 relay contacts
Power consumption 0.4 W standby
max. 1 W without load
Max. contact load 6.0 A / 1,500 VA
• ohmic load cos =1 4.8 A / 1,200 VA
• inductive load cos =0,8
Protection degree IP20
Operating temperature -20 °C to +45 °C
Dimensions (W/L/H) 34.5 / 89.6 / 62.8 mm
Weight 108 g
EN 4
LED 3TB and
> 1,6 s
LED1 or LED2 flash
Display: centre line flashes
LED output + 3TB + 2TB
> 1,6 s
light up
Button to press Display
1x briefly LED 3TB flashes
or
2x briefly LED 2TB flashes
L
repeatedly
LED 1 or LED 2 + LED
or
xTB flash
LED 3TB + 2TB and LED 1
> 1,6 s
or LED 2 flash quickly
Transmitter LED 3TB + 2TB and LED 1
button x or LED 2 light up.
1x briefly When all the LEDs go out,
the receiver is ready for
operation
Button to press Display
1x briefly LED 3TB flashes
or
2x briefly LED 2TB flashes
L
repeatedly
LED 1 or LED 2 + LED
or
xTB flash
LED 3TB + 2TB and LED 1
> 1,6 s
or LED 2 flash quickly
LED 3TB + 2TB and LED 1
until
or LED 2 light up.
> 1,6 s
When all the LEDs go out,
the receiver is ready for
operation
EN
Warnings regarding installation
The installation of products that will permanently be part of the electrical installation and which
include dangerous voltages, shall be carried out by a qualified installer and in accordance with
the applicable regulations. This user manual must be presented to the user. It should be included
in the electrical installation file and it should be passed on to any new owners. Additional copies
are available on the Niko website or via Niko customer services.
EN
CE marking
This product complies with all of the relevant European guidelines and regulations. For radio
equipment Niko llc declares that the radio equipment in this manual conforms with the 2014/53/EU
directive. If applicable, the full text of the EU Declaration of Conformity can be found on www.niko.eu.
EN
Environment
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point.
Together with producers and importers, you have an important role to play in the advancement of
sorting, recycling and reusing discarded electrical and electronic appliances. In order to finance
the waste collection and processing, the government levies a recycling contribution in some cases
(included in the purchase price of this product).
PM410-00352R21224