Black & Decker CS1550 Mode D'emploi page 6

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
ENGLISH
Residual risks
The following risks are inherent to the use of saws:
Injuries caused by touching the rotating parts.
u
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
Impairment of hearing.
u
Risk of accidents caused by the uncovered parts of the
u
rotating saw blade.
Risk of injury when changing the blade.
u
Risk of squeezing fingers when opening the guards.
u
Health hazards caused by breathing dust developed when
u
sawing wood, especially oak, beech and MDF.
Saw blades
Do not use blades of larger or smaller diameter than
u
recommended. For the proper blade rating refer to the
technical data. Use only the blades specified in this
manual, complying with EN 847-1.
Warning! Never use abrasive wheels.
u
Safety of others
This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
u
play with the appliance.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by EN
60745 and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
6
(Original instructions)
Labels on tool
The following symbols, along with the date code, are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Lock-off button
3. Main handle
4. Secondary handle
5. Spindle lock button
6. Shoe
7. Saw blade
8. Saw blade guard
9. Guard handle
10. Saw dust outlet
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped.
Removing and fitting a saw blade (fig. A)
Removing
Keep the spindle lock button (5) depressed and rotate the
u
blade until the spindle lock engages.
Loosen and remove the blade retaining screw (11) by turn-
u
ing it counterclockwise using the spanner (12) supplied.
Remove the outer washer (13).
u
Remove the saw blade (7).
u
Fitting
Place the saw blade onto the inner flange (14), making
u
sure that the arrow on the blade points in the same direc-
tion as the arrow on the tool.
Fit the outer washer (13) on the spindle, with the raised
u
part pointing away from the saw blade.
Insert the blade retaining screw (11) into the hole.
u
Keep the spindle lock button (5) depressed.
u

Publicité

Table des Matières
loading

Table des Matières