Rev-A-Shelf 4VWTM-1220DM-2 Notice D'installation

INSTALLATION INSTRUCTIONS
for 4VWTM-1220DM-2
INSTRUCCIONES DE INSTALACIÓN
Para 4VWTM-1220DM-2
NOTICE D'INSTALLATION
De la 4VWTM-1220DM-2
STEP 1:
Install front bracket to
Rear Mounting Bracket
front side of slide.
Step 1: Install rear bracket to rear of slide.
Paso 1: Instale el soporte trasero en la parte posterior de la deslizadera.
Étape 1: Attacher le support arrière à l'arrière de la glissière.
STEP 2:
Install rear bracket to
rear of slide.
Step 2:
Paso 2: Instale la parte delantera de la deslizadera en el bastidor
La parte inferior de la deslizadera debe estar a 19,7 cm (7 ¾ pulg.) del piso
1
14 / "
4
1 1
13 / " 13 / "
2 2
Front View
STEP 3:
Étape 2: Monter l'avant de la glissière sur le cadre frontal. Le trou doit se
Mount slide to cabinet
if rear of cabinet is
doit se trouver à 19,7 cm (7 ¾ po) du fond de l'armoire. Utiliser une vis à
thinner then 1/2" install
a 1/2" x 3" wide furring
strip to the back of the
cabinet centered
Step 3: If rear of cabinet is thinner then ½", install a ½" x 3" wide furring
14 1/4" from floor of
cabinet.
Paso 3: Si el grosor de la parte trasera del armario es inferior a
13 mm (½ pulg.), instale un listón de 13
x 76 mm (½ x 3 pulg.) de ancho
centrada en la parte trasera y a 22,5 cm
Étape 3: Si l'arrière de l'armoire est
1
14 / "
4
moins épais que 13 mm (½ po),
attacher un tasseau de
1
13 / " 13
2
13mm x 76mm (½ x 3 po) à l'arrière de
fond de l'armoire.
7 ¾" MIN
7 ¾" MIN
I-4VWTM
Furring
Strips
1
14 / "
4
1
13 / "
2
Furring
Strips
1
/ "
2
Front View
STEP 4:
Measure from inside
cabinet wall to inside
face frame (A) distance
should be measured
the same at rear of
cabinet (B).
STEP 5:
Position the slide with front
Step 4: Measure from inside cabinet wall to inside face frame (A) distance
bracket on the face frame
should be measured the same at rear of cabinet (B).
opening and move it forward
Paso 4: La medida de la pared interior del armario a la parte
until the self register stop hits the
interior del bastidor delantero
inside of the face frame opening.
(A) debe ser similar en la parte
STEP 4:
posterior del armario (B).
Bottom of slide should be 13 1/2"
Measure from inside
Étape 4: Mesurer à partir
from cabinet floor. Install screw in
de la paroi intérieure de
cabinet wall to inside
slotted mounting hole, do not
l'armoire jusqu'à l'intérieur du
face frame (A) distance
tighten. Extend the slide rear mounting bracket until it
cadre frontal (A). Mesurer la
should be measured
contacts the rear Furring strip. Bottom of slide should be
même distance à l'arrière de
the same at rear of
13 1/2" from cabinet floor. Rear mounting bracket should
l'armoire (B).
cabinet (B).
be the same distance from the side cabinet wall at rear of
slide as it is up front. Drive mounting screw in center
horizontal slot of rear mounting bracket, tighten.
Tighten screw in front bracket.
STEP 5:
Position the slide with front Step 5: Mount Rear Bracket. Extend the slide rear mounting bracket until it
STEP 6:
contacts the rear (Furring Strip). Bottom of slide should be 7 ¾" from cabinet
bracket on the face frame
Install wood unit (with slides attached) into cabinet,
opening and move it forward
engaging product member slides into cabinet member
cabinet wall at rear of slide as it is up front. Drive mounting screw in center
until the self register stop hits the
slides, push
horizontal slot of rear mounting bracket, tighten. Tighten screw in front
inside of the face frame opening.
unit until it
bracket.
Bottom of slide should be 13 1/2"
locks in place.
Paso 5: Monte el soporte trasero. Extienda el soporte trasero de la
from cabinet floor. Install screw in
deslizadera hasta que toque atrás (el listón trasero). La parte inferior de
Now you are
slotted mounting hole, do not
la deslizadera debe estar a 19,7 cm (7 ¾" pulg.) del piso del armario. La
ready to
tighten. Extend the slide rear mounting bracket until it
distancia entre la parte posterior de la pared del armario a la deslizadera del
mount the
contacts the rear Furring strip. Bottom of slide should be
soporte de montaje trasero debe ser similar a la que tiene con respecto al
door.
frente. Introduzca el tornillo de montaje en la ranura horizontal que está en
13 1/2" from cabinet floor. Rear mounting bracket should
el centro del soporte de montaje trasero y apriételo. Apriete el tornillo en el
be the same distance from the side cabinet wall at rear of
STEP 7:
soporte delantero.
slide as it is up front. Drive mounting screw in center
See door mounting instructions on inside.
Étape 5: Monter le support arrière. Étendre le support de montage arrière
horizontal slot of rear mounting bracket, tighten.
de la glissière jusqu'à ce qu'il touche l'arrière (le tasseau). Le dessous de la
Tighten screw in front bracket.
glissière doit se trouver à 19,7 cm (7 ¾" po) du fond de l'armoire. La distance
séparant le support de montage arrière de la paroi latérale de l'armoire doit
STEP 6:
être identique à l'arrière et à l'avant. Placer une vis de montage dans la fente
Install wood unit (with slides attached) into cabinet,
horizontale du centre du support de montage arrière et la serrer. Serrer la
engaging product member slides into cabinet member
vis du support avant.
slides, push
1
14 / "
4
unit until it
locks in place.
1
13 / "
2
Now you are
ready to
mount the
door.
STEP 7:
See door mounting instructions on inside.
Step 6: Install wood unit (with slides attached) into cabinet, engaging
product member slides into cabinet member slides push unit until it locks
in place.
Paso 6: Instale la pieza de madera (con las deslizaderas instaladas) en
el armario de forma que las deslizaderas en el producto se entren en las
deslizaderas que están en el armario y empuje hasta que cierren.
Étape 6: Installer l'ensemble en bois (avec les glissières montées) dans
l'armoire en engageant les glissières du produit dans celles de l'armoire.
Pousser sur l'ensemble jusqu'à ce qu'il s'enclenche.
Face Frame
(A)
Cabinet Member
Slides
(B)
12400 EARL JONES WAY • LOUISVILLE, KY 40299 • 800 626 1126
Furring Strips
(A)
Cabinet Member
(B)
Product Member
Product Member
Self
Register
Stop
Top View
Face Frame Face Frame
Slides
Furring Strips
Self
Register
Stop
Cabinet Member
Cabinet Member