Publicité
Liens rapides
WOOD TWO–TIERED DRAWER
TOOLS REQUIRED:
#2
7
64
#2
ESTIMATED ASSEMBLY TIME:
20 MIN
CARE AND MAINTENANCE:
Clean with a damp cloth and
wipe parts dry.
NOTE:
The wood two–tiered drawer
is designed to use either
BLUMOTION 563F5330B
under mount slides or Grass
Elite 7523-19/550/533 under
mount slides.
4WTCD-30 & 4WTCD-36 with
BLUMOTION slides require an
additional stabilizer bar which
is included in the kit purchase.
For video instruction visit:
rev-a-shelf.com/videos
4WTCD-343FLSC
4WTCD-419FL
4WTCD-15
4WTCD-30
THE WOOD TWO–TIERED DRAWER (WTCD) IS DESIGNED
TO USE UNDER MOUNT FULL-EXTENSION DRAWER
HARDWARE ONLY. IF YOU ARE REPLACING A DRAWER
BOX THAT DOES NOT CURRENTLY USE FULL-EXTENSION
(FX) OR PREMIUM GUIDE (PG) HARDWARE YOU WILL
NEED TO ORDER A DRAWER GUIDE KIT (DGK).
INSTALLATION INSTRUCTIONS: WOOD TWO–TIERED DRAWER
4WTCD-495FL
4WTCD-18
4WTCD-21
4WTCD-36
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
JUST ADD
YOUR OWN
DRAWER
FRONT!
4WTCD-572FL
4WTCD-24
4WTCD-18-KCUP
I-4WTCD-TRI-0116
Publicité
Manuels Connexes pour Rev-A-Shelf 4WTCD-18-KCUP
Sommaire des Matières pour Rev-A-Shelf 4WTCD-18-KCUP
- Page 1 ESTIMATED ASSEMBLY TIME: 20 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry. 4WTCD-30 4WTCD-36 4WTCD-18-KCUP NOTE: The wood two–tiered drawer is designed to use either BLUMOTION 563F5330B under mount slides or Grass Elite 7523-19/550/533 under mount slides.
- Page 2 Using the provided screws, attach your left and right sided triggers. NOTE Release triggers are side sensitive and are marked with an “L” & “R” for Left and Right. Customer Service: 800-626-1126 | rev-a-shelf.com...
- Page 3 STEP 3 FIG. Secure a Figure 8 fastener on each side of the drawer box front using the pre-drilled pilot hole as a locator. Once the (2) Figure 8 fasteners have been secured to the drawer box place the drawer box on the back of the drawer front from Step one.
- Page 5 Grass Elite 7523-19/550/533. Los sistemas de rieles 4WTCD-30 & 4WTCD-36 con 4WTCD-30 4WTCD-36 4WTCD-18-KCUP BLUMOTION, requieren una barra estabilizadora adicional la cual se incluye en este equipo adquirido. Nettoyez avec un linge humide et essuyez les pièces pour les sécher complètement.
- Page 6 REMARQUE Les gâchettes de dégagement doivent être installées sur le bon côté et elles sont marquées d’un “L” et “R” pour le côté gauche (“L”) ou le côté droit (“R”). Customer Service: 800-626-1126 | rev-a-shelf.com...
- Page 7 PASO 3 STEP 1 ÉTAPE 3 FIG. Asegure el cierre de la igura 8 a cada lado de la parte frontal del cajón, usando los oriicios pre taladrados como punto de referencia. Una vez que los dos cierres de la igura 8 estén asegurados a la caja, coloque la caja en la parte posterior del cajón del paso número 1.
- Page 8 /vers l’arrière. Ajustez au besoin pour vous assurer que la façade du tiroir s’aligne avec les armoires adjacentes. Voir l’Illustration 4 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 Customer Service: 800-626-1126 | rev-a-shelf.com...