Volvo Penta Easy Connect NMEA 2000 Instructions De Montage page 8

Read through the instructions before you begin to work.
Check that all parts are included in the package.
Items in illustrations in the instructions may differ from
the model being worked on. The illustrations are used
for different instructions and may therefore vary between
engine models. The essential information is correct.
Bluetooth code
Note: you will need the six-digit bluetooth code printed on
the interface label for connection to your device (phone,
tablet, etc.). Refer to C in Fig. 8. Record the code number
here before mounting the interface.
Bluetooth code: ..................................................
Part no 23870792
Interface 1
23197513
Harness
23305065
Harness
948210
2
Cable ties
WARNING!
Prevent accidental starting:
Disconnect engine power at the battery switch, tag bat-
tery switch and all ignition switches to alert others that
work is being done on the engine.
NOTICE!
The interface and adapter harnesses must be mounted
securely, away from moving parts, excess heat, and
wet areas. Use the cable ties to secure the interface.
All harness and cable installations must meet ABYC,
USCG, EU and other applicable regulations and stan-
dards.Mount the interface where the LED lights can be
seen, for system diagnostics.
EVC 2.0, EVC-E and EVC-D
Refer to Figure 1.
Option A - directly to the multilink hub.
Option B - use Y-cable to install in-line.
Gas engines without EVC system
Refer to Figure 2.
Extension harnesses must be ordered if the interface is
mounted away from the engine. For twin installations, use
one interface on each engine.
A - Easy Connect connector on engine (2019 to present)
No adapter cable needed. Connector is on the rear of the
engine.
B - 6-pin VODIA connector (2010 to 2019). Use adapter
harness 23305065 to connect the interface to the engine
harness VODIA connector. The connector is located near
the fuse box.
C - 8-pin VODIA connector (2006-2009) An additional
harness is needed to complete the installation. Order one
3883170 adapter harness for each engine. Install the
interface and adapter harnesses according to figure 2.
B and C The Vodia connector is still powered at key
off; the LEDs are still active and will draw a very small
amount of current. During storage this could drain the bat-
teries; disconnect engine electrical power to prevent.
23870793 23870794
1 1
1
1
2 2
Earlier EVC versions
EVC-C refer to Figure 3.
EVC-B refer to Figure 4.
EVC-A refer to Figure 5:
Y-harness 23789703 is required to connect the interface
to the EVC network. The third leg of the Y-harness must
be terminated. On twin installations this leg is connected
to X5 on the second HCU, which provides the termination.
On single installations terminal plug 881829 must be
installed on the open leg.
MDI refer to Figure 6.
D1/D2 MDI refer to Figure 7.
Use cable 23900247 to connect to the multilink and
NMEA 2000 backbone. This connection powers the inter-
face when the engine is not running.
NMEA2000
The interface will also broadcast data from the boat's
NMEA 2000 network. Connect the interface's NMEA 2000
connector to the NMEA 2000 backbone to access this
data.
System Status LEDs
Refer to Figure 8.
G - Green LED - diagnostics; Flashes On-Off-On-Off-On,
the device has power supply and communication on both
NMEA and EVC/Engine.
On constantly, the unit has power supply but no communi-
cation, either on NMEA or EVC/Engine.
Flashing twice and then off (500 ms), repeatedly, then
the unit has power supply and communication on EVC/
Engine but not on NMEA.
Flashing three times and then off (500ms), repeatedly,
then the unit has power supply and communication on
NMEA but not on EVC/Engine.
B - Blue LED - bluetooth status; Flashes On-Off-On-Off-
On, unit is paired and working.
Not lit, bluetooth device in interface is not working.
On constantly, bluetooth interface is working but not
paired. Flashing twice and then off (500 ms), repeatedly,
error in bluetooth communication.