Work Area; Personal Safety - Husky HDS580 Mode D'emploi

Operating Instructions
Important Safety Instructions
(Continued)

WORK AREA

Never
spray
closer than 25 feet to the
compressor! If possible,
locate compressor in
separate room. Never spray into
the compressor, compressor
controls or the motor.
Do not
spray
flammable materials in
vicinity of open flame
or near ignition sources.
Motors, electrical equipment and
controls can cause electrical arcs
that will ignite a flammable gas
or vapor. Never store flammable
liquids or gases in the vicinity of
the compressor.
Do not smoke or
eat when spraying
paint, insecticides, or other
flammable substances.
Keep hose away
from sharp
objects. Bursting air hoses may
cause injury. Examine air hoses
regularly and replace if damaged.
Always work in a
clean
environment. To avoid injury and
damage to the workpiece, do not
aim the spray gun at any dust or
debris.
Keep visitors
away and NEVER
allow children or pets in the work
area.

PERSONAL SAFETY

a. Stay alert. Watch what you are
doing and use common sense
when operating the tool. Do not
use the tool while tired or under
the influence of drugs, alcohol,
or medication. A moment of
inattention while operating the
tool increases the risk of injury to
persons.
b. Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long
hair increases the risk of injury to
persons as a result of being caught
in moving parts.
c. Do not attach the hose or tool to
your body. Attach the hose to the
structure to reduce the risk of loss of
balance if the hose shifts.
Use a
face
mask / respirator and
protective clothing when
spraying. Always spray in
a well ventilated area to prevent
health and fire hazards. Refer to
Material Safety Data Sheets (MSDS)
of spray material for details.
Always
wear eye
protection.
Never
use
oxygen, corbon dioxide,
combustible gases or
any bottled gas as an
air source for the spray gun. Such
gases are capable of explosion and
serious injury to persons.
Do not misuse this
product. Excessive
exposure to vibration, work in
awkward positions, and repetitive
work motions can cause injury
to hands and arms. Stop using
any tool if discomfort, numbness,
tingling or pain occur, and consult a
physician.
Never aim or
spray at yourself
or anyone else or serious injury
could occur.
Do not spray
acids, corrosive
materials, toxic chemicals,
fertilizers or pesticides. Using these
materials could result in death or
serious injury.
When spraying
and cleaning,
always follow the instructions and
safety precautions provided by the
material manufacturer (Refer to
MSDS).
Do
not
overreach. Keep proper
footing and balance at
all times. Proper footing
and balance enables better control
of the spray gun in unexpected
situations.
2
TOOL USE AND CARE
a. Use clamps or another practical way
to secure and support the workpiece
to a stable platform. Holding the
work by hand or against the body is
unstable and is able to lead to loss
of control.
b. Store the tool when it is idle out
of reach of children and other
untrained persons. A tool is
dangerous in the hands of untrained
users.
use pressure that exceeds
operating pressure of the
spray gun or any of the
parts (hoses, fittings, etc.) in the
O
painting system.
CO
2
able to result in bursting, abnormal
operation, breakage of the spray
gun or serious injury to persons.
the spray gun that the air source
has been adjusted to the rated air
pressure or within the rated air-
pressure range.
or binding of moving parts,
breakage of parts, and any other
condition that affects the spray
gun's operation. If damaged, have
the spray gun serviced before
using. Many accidents are caused
by poorly maintained spray guns.
There is a risk of bursting if the
spray gun is damaged.
starting. Be sure the trigger is
off before connecting to the air
supply. Do not carry the spray gun
with your finger on the trigger or
connect the spray gun to the air
supply with the trigger on.
the air source before, changing
accessories, cleaning, servicing
or storing the spray gun. Such
preventive safety measures reduce
the risk of starting the spray gun
unintentionally.
water / oil removal equipment may
result in damage to machinery or
workpiece.
on the air supply to the spray gun.
Do not
Over pressurizing
the spray gun is
Always verify
prior to using
Check for
misalignment
Avoid
unintentional
Disconnect the
spray gun from
Failure to install
appropriate
Always use a
pressure regulator