Technical Data; Maintenance And Cleaning - Speaka Professional 1331007 Mode D'emploi

Troubleshooting
No audio signal available
• Is the slide switch (4) in the correct switch position?
The slide switch must be in the "L/R" position if an analogue audio signal is fed to the stereo
jack plug.
The slide switch must be brought to the "Optical" position when connecting a digital optical
audio signal to the TOSLINK jack.
• Check the player to find the presence of an audio signal.
If the optical input is used then you note that a 2-channel stereo signal ("LPCM 2CH") or at
most a 5.1 audio signal ("DTS2....5.1CH") can be fed here.
If necessary, select a different audio format at the playback device (e.g. in the menu of the
Blu-ray player and in the audio settings of the Blu-ray disc).
• Check the volume setting on the TV.
• Check, if the mute function on any of the devices connected is activated.
• The audio inserter can work only if it is powered. Therefore, check whether the power adapter
is properly connected and the audio inserter has been turned on.
No image
• A suitable HDMI cable must be used for 3D or 4K-resolution.
• Use a shorter cable in a trial-and-error manner.
• The audio inserter can work only if it is powered. Therefore, check whether the power adapter
is properly connected and the audio inserter has been turned on.
Handling
• Use is permitted only in dry indoor locations. The product must not get damp or wet! There is
a risk of a life-threatening electric shock!
• Never use the product immediately after it has been taken from a cold room to a warm one.
The condensation that forms can ruin the product under certain circumstances. A power
adapter also carries the risk of a potentially fatal electric shock!
Allow the product to reach room temperature before connecting it to the power supply and
putting it to use. This may take several hours.
• Any maintenance or repair work may only be performed by an authorised repair shop.
• When setting up the product, make sure that the cables are neither kinked nor pinched.
• Prevent the following adverse conditions at the location of installation and during transport:
- Dampness or excessive humidity
- Extreme cold or heat, direct sunlight
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows
- Strong magnetic fields such as those found in the vicinity of machinery or loudspeakers
Maintenance and cleaning
• The product does not require any maintenance. You should never take it apart. Any mainte-
nance or repair work may be performed only by an expert.
• Before you clean the product, disconnect it from the mains voltage. Pull the power adapter
from the mains socket.
• The outside of the product should be cleaned only with a clean, soft, dry cloth.
Do not use aggressive cleaning agents or chemical solutions that could damage the housing
(discolouring) or impair operation.
• Dust can easily be removed using a clean, long-bristle brush and a vacuum cleaner.
Disposal
The product must not be disposed of in the household waste!
Please dispose of the product at the end of its service life according to the current
statutory requirements.
Technical data
a) Audio inserter
Input...................................... 1x HDMI
.............................................. 1x stereo analogue input (jack plug 3.5 mm)
.............................................. 1x optical digital input (TOSLINK)
Output ................................... 1x HDMI
3D-support ........................... yes
4K-support ............................ yes
Max. transmission rate ......... 10.2 Gbps
Compatible with .................... HDCP 1.2, DVI 1.0
Sampling rate ....................... up to 192 kHz (at the optical digital input)
Cable lengths ........................ 1080p/8bit: max. 15 m each at the HDMI input/output
.............................................. 1080p/12bit or 4K: max. 10 m each at the HDMI input/output
Ambient conditions ............... Temperature 0 °C to +40 °C; humidity 10% to 85%, non-con-
densing
Dimensions ........................... 95 x 82 x 24 mm (W x D x H)
Weight .................................. 194 g
b) Wall plug transformer
Operating voltage ................. 100 - 240 V/AC, 50/60 Hz
Output ................................... 5 V/DC, 2 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.