Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4.12 Child Lock
Use child lock function to prevent children from
tampering with the machine. Thus you can avoid any
changes in a running programme.
C
If the Programme Selection knob is turned
when the Child Lock is active, "Con" appears on
the display. The Child Lock does not allow any
change in the programmes and the selected
temperature, speed and auxiliary functions.
C
Even if another programme is selected with the
Programme Selection knob while the Child Lock
is active, previously selected programme will
continue running.
C
When the Child Lock is active and the machine
is running, you can switch the machine to Pause
mode without deactivating the Child Lock by
turning the Programme Selection knob to On
/ Off position. When you turn the Programme
Selection knob afterwards, the programme will
resu
To activate the Child Lock:
Press and hold 1st and 2nd Auxiliary Function
buttons for 3 seconds. The lights on the 1st and 2nd
Auxiliary Function buttons will flash while you keep
the buttons pressed for 3 seconds.
To deactivate the Child Lock:
Press and hold 1st and 2nd auxiliary function buttons
for 3 seconds while any programme is running. The
lights on the 1st and 2nd Auxiliary Function buttons
will flash while you keep the buttons pressed for 3
seconds.
C
In addition to the method above, to deactivate
the Child Lock, switch the Programme Selection
knob to On / Off position when no programme is
running, and select another programme.
C
When the power is restored after a power failure
or after your machine is unplugged and plugged
in again, the Child Lock will not be deactivated
when the machine resumes operating.
4.13 Progress of programme
Progress of a running programme can be followed
from the Programme Follow-up indicator. At the
beginning of every programme step, the relevant
indicator light will turn on and light of the completed
step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make must
be in a step after the running programme step. If the
change is not compatible, relevant lights will flash
for 3 times.
18 / EN
C
If the machine does not pass to the spinning
step, Rinse Hold function might be active or the
automatic unbalanced load detection system
might be activated due to the unbalanced
distribution of the laundry in the machine.
4.14 Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
when the water level is unsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine checks
the level of the water inside. If the level is suitable,
Loading Door light illuminates steadily within 1-2
minutes and the loading door can be opened.
If the level is unsuitable, Loading Door light turns off
and the loading door cannot be opened. If you are
obliged to open the Loading Door while the Loading
Door light is off, you have to cancel the current
programme; see "Canceling the programme".
Changing the selections after programme
has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine
to pause mode while a programme is running. The
light of the step which the machine is in starts
flashing in the Programme Follow-up indicator to
show that the machine has been switched to the
pause mode.
Also, when the loading door is ready to be opened,
Loading Door light will also illuminate continuously in
addition to the programme step light.
Changing the speed and temperature settings for
auxiliary functions
Depending on the step the programme has reached,
you may cancel or activate the auxiliary functions;
see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C
If no change is allowed, the relevant light will
flash for 3 times.
4.15 Adding or taking out laundry
Press the Start / Pause button to switch the machine
to pause mode. The programme follow-up light of
the relevant step during which the machine was
switched into the pause mode will flash. Wait until
the Loading Door can be opened. Open the Loading
Door and add or take out the laundry. Close the
Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press
Start / Pause button to start the machine.
Washing Machine / User's Manual
Publicité
Table des Matières
