Important Notes For Installer; Description And Technical Specifications; Electrical Equipment (Standards System); Installation Of Automation - FAAC 390 Mode D'emploi

Thank you for choosing our product. FAAC is sure that it will give you
all the performances you are looking for. All our products are the
result of a long experience in the field of the automated systems.
In the middle of the handbook you will find a detachable
brochure with the images for the installation.
These instructions apply to the following model:
The external automation with articulated arms automates residen-
tial swing-leaf gates with leaves of up to 3m in length, and is ideal
for applications on large pilasters without the need to provide
niches (sometimes required to observe the installation dimensions
of piston driven devices).
It consists of an irreversible electro-mechanical operator with guard
and an articulated-arm activation system to be fitted to the gate
with the appropriate accessories.
The irreversible system ensures the gate is mechanical locked when
the motor is not operating. No lock need be installed for leaves
up to 2m in length.
A manual release makes it possible to move the gate in the event
of a power-cut or fault.

IMPORTANT NOTES FOR INSTALLER

• Before starting the installation of the operator read this manual
completely.
• Keep this manual for future reference.
• Smooth operation and specifications are obtained only declared
following the directions given in this handbook and with acces-
sories and safety devices FAAC.
• The lack of a mechanical clutch device requires to ensure an
adequate level of security automation, the use of a central control
device with an electronically controlled clutch.
• The automation was designed and built to control vehicular ac-
cess. Avoid any other use.
• The operator can not be used to handle emergency exit routes
or gates installed on emergency (escape routes).
• If there is built-in anti motorize from a door to the walkway is requi-
red to add a safety switch on the door, connected on the entry of
STOP , to inhibit the operation of automation with door open.
• Everything that is not expressly stated in this manual is not al-
lowed.

1. DESCRIPTION AND TECHNICAL SPECIFICATIONS

With reference to Figure 1
Pos
Guard
a
Operator securing base-plate
b
Release wrench
c
Release
d
Gearmotor
e
Transmission shaft
f
Straight lever of articulated arm
g
Curved lever of articulated arm
h
Front coupling
i
TAB. 1 TECHNICAL SPECIFICATION OF OPERATOR
MODEL
Power supply
Power absorption
Current absorption
Max torque
Nominal Torque
Starting capacitor
Leaf max length
a
Thermal protection for winding
Reduction ratio
Angular velocity
Ambient temperature
Use frequency at 20°C
Cycles / hour at 20°C
Noise
390
Description
390
230V~ 50Hz 24 Vdc
280 W 40 W
1.2 A 2 A
250 Nm 200 Nm
170 Nm 140 Nm
8 µF /
3 m
140 °C /
1:700
8 °/sec
-20 °C +55 °C
S3 - 30% S3 - 100%
>30 >100
<70 dB(A)
MODEL
Weight of gearmotor
Protection class
Gearmotor overall dimension
An electrolock should be installed in the event of leaves excee-
a
ding 2 metres, in order to guarantee the leaf blocking.

2. ELECTRICAL EQUIPMENT (standards system)

With reference to Figure 3
Pos. Description
Operators
a
TX photocells
b
RX photocells
c
Key selector
d
Flashing lamp
e
Control unit
f
Mechanical stops
g
To lay electrical cables, use adequate rigid and/or flexible
tubes.
Always separate low voltage accessories from those ope-
rating at 230 V~. To avoid any interference, always use
separate sheaths.
For the motor cable to use a sheath suitable for outdoor use,
a hand that is piped in special ducts always external use.

3. INSTALLATION OF AUTOMATION

3.1. PRELIMINARY CHECKS

To ensure safety and an efficient automation, make sure the
following requirements are met:
• The gate structure must be suitable for automation. In particular,
make sure it is sufficiently sturdy and rigid, and that its dimensions
are in line with those indicated in the technical specifications.
• Make sure that the leaves move properly and uniformly, without
any irregular friction during their entire travel.
• Check if hinges are in good condition.
• Make sure the travel limit mechanical stops are present. We
advise you to carry out any metalwork jobs before installing the
automation.

3.2. INSTALLATION DIMENSIONS

Establish the installation position of the operator by consulting
Fig. 4-5-6.
INWARD OPENING (Fig. 5)
A (mm) B (mm)
60 ÷ 110
110 ÷ 160
160 ÷ 210
110 ÷ 130
210 ÷ 260
260 ÷ 310
310 ÷ 360
60 ÷ 110 190 ÷ 210
110 ÷ 160 230 ÷ 250
160 ÷ 210 290 ÷ 310
210 ÷ 260 310 ÷ 330
As for 120° openings the curved arm must be fixed to the
hole marked with the letter "X"
OUTWARD OPENING (Fig. 6)
A (mm) B (mm)
60 ÷ 110
110 ÷ 160
160 ÷ 210 110 ÷ 130
210 ÷ 260
260 ÷ 310
390 / 390 24 Page 
Guide for the installer
390
11.5 Kg
IP 44
Vedi Fig. 2
Cables
230 Vac 24 Vdc
4x1 mm 2x1.5mm
2
2x0.5 mm
2
4x0.5 mm
2
2x0.5 mm
2
2x1.5 mm
2
3x1.5 mm (power supply)
2
—
a (°)
C max. (mm)
730
720
710
90
700
690
670
650
600 120
540
510 120
a (°)
C max. (mm)
430
380
330 90
280
240
2