Diamond EXPONORM 650 P Mode D'emploi page 5

Operator's guide:
1. Unpacking instructions
2. The handle
3. The fish trays
I
4. The drip tray
5. Internal cleaning
UK
6. External cleaning
7. Connection to the mains
D
8. Controls
9. Checking correct operation
E
F
! WARNINGS
It is most important that this instruction booklet is kept together with the appliance both for future
NL
reference and for reasons of safety. 1. Adults should operate this appliance only. Do not allow children
to use the controls or play with it. 2
P
characteristics of this appliance. . The electrical installation of the appliance should be carried out by a
qualified electrician or other competent person. . Never attempt to carry out repairs unassisted. Inexpert
S
repairs can cause serious damage and malfunction. . Assistance has to be provided by an authorized
engineer only. Always use original spare parts. . This appliance is not suitable for the storage of basic
DK
commodities not including food-stuffs. . The manufacturers of this appliance accept no responsibility for
the consequences of misuse in contravention of these safety instructions. It further reserves the right to
carry out improvements without prior notice. 8
FIN
9 . Nevere install the appliance near sources of heat, such as radiators, stoves, etc.
ventilation grills free from obstruction for at least 30 cm.
B
shelves and grills do not hang over the edges.
ice to form on the evaporator, we recommend stopping the compressor and placing the goods in special
GR
refrigerated containers, kept at the same temperature, until defrosting is completed;if this is not carried
out the compressor will continue to operate leading to a wasteful consumption of electricity and poor
CZ
performance.
least 10 cm.
EE
! Our products are for internal use only do not install outside restaurants, shops
LV
LT
H
1. UNPACKING INSTRUCTIONS
M
CARDBOARD PACKAGE 1a.
Remove the nails from the wooden crate with care.
PL
and pallet or crate.
the front corners.
SK the package before disposal.
2. THE HANDLE
SLO
1. The handle can be found inside the appliance in a bag.
frame using the two screws already inserted in the holes. Tighten with care.
over the metal handle and press down until it clicks into place (see figure 2).
3. THE FISH TRAYS
On request, the appliance can be supplied with fish trays; one of these has a rounded corner to be placed
in the corner of the cabinet housing the refrigeration pipe. The trays are supplied with a perforated bottom
for water drainage, which is easily removable for cleaning (see figure 3).
4. THE DRIP TRAY
Take the plastic tray from inside the cabinet and slide it onto the guides underneath the cabinet (see
figure 4).
5. INTERNAL CLEANING
1. Remove the protective film from the aluminium tray support.
panels with a soft, damp sponge and a neutral detergent.
fluorescent lights should be cleaned with a soft damp sponge, avoiding the use of substances containing
alcohol or other solvents, which could damage the tubing.
6. EXTERNAL CLEANING
1. Use the same products as used for the internal cleaning.
panels and grilles (see figure 5).
. It is forbidden to modify in any way the main functions and
3
7
13 . If the appliance is not working and unused,it is indispensable to keep the door open at
Cut the strap and lift up the cardboard package.
3. Lift the appliance.
6. Place the appliance on a flat and level surface.
8. Separate the packaging materials to facilitate disposal (see figure 1).
Operator's guide
10. Replacing the internal lights
11. Replacing the door's magnetic gasket
Maintenance manual (Page 48):
1. Cleaning the condenser
2. Internal cleaning
3. Replacing a glass panel
4. Wiring diagram diagram of refrigeration unit
4
5
6
. Avoid installing the cabinet directly in line with sunlight.
11 .Ensure that the products displayed on the
12 . If damp air or products to be refrigerated should cause
2. Insert the forks of a forklift truck between appliance
4. Remove the pallet or crate.
2. Fix the metal part of the handle to the door
2. Clean the internal surfaces and glass
3. The transparent tubular covers for the
4. Dry with a soft, clean cloth.
2. Remove the protective film from the steel
6
10 . Keep the
WOODEN CRATE 1b.
5. Screw the adjustable feet onto
7. Make sure there is nothing left in
3. Place the plastic insert