Meccanica Fadini Elpro S20 Mode D'emploi page 9

Programmateur électronique pour le controle jusqu' à deux bornes escamotables, avec ou sans le fin de course
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 14
Elpro S20
GB
63 64 65 66
60 61
Fuse 1 A
Red
Yellow
Green
(Optional: plug-in PCB for traffic
light to suit 230 V lamp)
code 7282L
STRIP jumper
LIMIT SWITCH
LIMIT SWITCH DIAGNOSTIC
Coral, Vigilo, Talos, Talos M30, Strabuc 930 Opinat range of bollards with limit switch: with the STRIP jumper inserted (as in the picture), Elpro S20
checks cyclicly every 10 minutes that the closing limit switches (post raised) are in the correct position; should any of them fail to be such, only the
motor of the post not in position is operated until this is fully up as required.
Note well: whenever Elpro S20 is re-powered, wait 10 seconds for the logic to become fully operating again.
The electronic control panel Elpro S20 is designed to operate the Talos, Talos M30, Strabuc 930 Opinat, Coral and Vigilo; power supply is
230 V single-phase.
Elpro S20 is capable of monitoring damages or malfunctioning with the system (ISC).
I.S.C. = Integrity and Supervision Circuit, is a special function of Elpro S20 which can self control the electronic PCB and detect any damages
occurring with any components or accessories. In this case, provided that the post is fitted with a release electric valve, lowering is allowed
automatically. The manufacturing company declines any responsability for incorrect handling and application; also, it reserves the right to
change or update the control panel any time.
IMPORTANT FOR THE INSTALLATION AND THE CORRECT FUNCTIONING:
- The control box must be installed in a dry and sheltered place; suitable holes are provided with the FADINI universal box for fitting
purpose and in case any commercial box is used, this must be adequate to the job.
- Make sure that power supply to the control board be 230 V ±10%.
- Make sure that power supply to the electric motor be 230 V ±10%.
- For distances longer than 50 metres increase the section of the wires.
- Fit the mains to the control box with a high sensitivity, 0,03 A, differential, magnetic-thermal circuit breaker.
- Cables with 1,5 mm² section wires are to be used for the power supply, electric motor and flasher for distances up to 50 m.
- Cables with 1 mm² section wires are to be used for the limit switches, photocells, push buttons and accessories.
N.W.: for applications such as light switching, CCTV, etc. use solid state relays to prevent the microprocessor from being affected.
IN CASE OF FAILURE OF THE PANEL:
- Check the electronic PCB voltage supply is 230 V ±10%.
- Check the electric motor power supply is 230 V ±10%.
- For longer distances increase wire section.
- Check fuses.
- The photocell contacts are closed.
- Check all NC contacts.
- The limit switches are properly connected and work correctly.
- In case the electric valve is fitted, check integrity with all fuses.
- Check that no voltage drop has occurred from the control board to the electric motor.
ELECTRONIC CONTROLLER UP TO 2 AUTOMATIC BOLLARDS,
WITH OR WITHOUT LIMIT SWITCH
PLUG-IN CONNECTOR FOR
3-LAMP TRAFFIC LIGHTS
MAX100 W EACH LAMP
T1
MOTOR RUN TIME
DWELL TIME
1 s - 22 s
1 s - 180 s
ON
OFF
1 2 3 4 5 6 7 8 9 10 11 12
RADIO
PLUG-IN CARD
CONNECTOR
Elpro S20
L1
L2
L3
L4
1 2 3 4 5 6 7 8 9 10
57 58
+
-
55 56
24 Vdc output
transformer
T2
L5
L6
L7
L8
L9
L10
11 12 13 14 15
9
20 VA - 50/60 Hz
Secondary
fuse
F4 = 2A
TRANSFORMER
L11
A
B A
16 17 18 19 20 21
M1
M2
1
2
2
Primary
fuse
transformer
F3 = 630 mA
51
52
53
Electric valve fuse,
acoustic device, flashing light
and led F5 = 2 A
Motor fuse M2
F2 = 5 A
Motor fuse M1
F1 = 5 A
B
Anti-disturbance filter
22
23
24 25
SYMBOLS:
NO contact
NC contact
Led ON
Led OFF
Pilot light
Flasher
ELPRO
S20
1
1 2

Publicité

Table des Matières
loading

Table des Matières