Technical Data; Before Starting The Equipment - Bavaria BCD 18 Li Instructions D'origine

4. Technical data

Motor power supply: ............................... 18 V DC
Idling speed: .......................... 0-350 / 0-1150 rpm
Torque settings: .......................................... 19+1
Clockwise/counter-clockwise: ........................Yes
Clamping range of drill chuck: .......... max. 10 mm
Battery charger output voltage: .............. 21 V DC
Battery charger output current: .................... 0.5 A
Charging unit supply voltage: ............ 100-240V~
50-60Hz
Battery type: ............................................... Li-Ion
Number of battery cells: ................................... 5
Battery capacitance: ................................. 1.5 Ah
Weight: .....................................................1.24 kg
Max. screw diameter: ................................. 6 mm
The maximum screw diameter indicates the ma-
ximum diameter of the screw that can be screwed
into wood. The screw diameter can vary depen-
ding on the type of wood.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ................... 61.13 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 72.13 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Drilling in metal
Vibration emission value a
K uncertainty = 1.5 m/s
Screwing without hammer action
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
Anl_BCD_18_Li_SPK9.indb 15 Anl_BCD_18_Li_SPK9.indb 15
GB
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

≤ 1.260 m/s
2
h,D
2
Be sure to read the following information before
you put the cordless screwdriver into operation:
1. Charge the battery only with the charging unit
≤ 0.687 m/s
2
supplied.
h
2
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
- 15 -
12.02.2018 15:32:36 12.02.2018 15:32:36