Tire Pressure - Remington Power Tools 13A277SF583 Notice D'utilisation

NOTE: Be certain the two seat tabs engage
the seat pivot bracket as shown in the
bottom right inset of Figure 2-6.
4. Select the desired position for the seat (b),
and secure with the adjustment knob (a)
removed in Step 1. See Figure 2-6.
5. To adjust the position of the seat, remove
the adjustment knob (a) on the bottom
of the seat (b). Slide the seat (b) forward
or backward as desired. Reinstall the
adjustment knob (a). See Figure 2-6.
Dash Shroud (If Equipped)
There are two shroud types. One shroud for the
1/3/5/K/T-Style and one for the S-Style dash.
Continue below for the 1/3/5/K/T-Style, skip
ahead to the S-style section for the S-style dash.
1/3/5/K/T-Style Dash
1. If the dash shroud (a) was shipped loose,
the hardware for attaching the dash
shroud (a) is shipped installed in the dash
(c). Remove the two bolts (b) from the
dash (c) . See Figure 2-7.
(a)
(b)
(b)
(a)
Figure 2-7
2. Mount the dash shroud (a) and align the
mounting holes. See Figure 2-7.
3. Secure the dash shroud (a) to the dash (c)
with the bolts (b) removed in Step 1. See
Figure 2-7.
S-Style Dash
1. If the dash shroud (a) was shipped loose, the
hardware for attaching the dash shroud (a) is
shipped installed in the dash shroud (a) and
the dash (b). Remove the two bolts (c) and
washers (d) from the dash (g) and two bolts
(e) and clips (f) from the dash shroud (b). See
Figure 2-8.
(a)
(d)
(c)
(f)
(b)
(e)
2. Mount the dash shroud (a) and align the
mounting holes. Using the bolts (c/e),
washers (d) and clips (f) install the dash
shroud (a) and snug the bolts (c) so that
the dash shroud (a) can be adjusted.
3. Close the hood and align the dash shroud
(a) to the hood (g) leaving a uniform gap
between the hood (g) and the dash shroud
(a).
4. Raise the hood (g) and tighten the bolts
(c)
(c/e) that hold the dash shroud (a) on the
dash (b).

Tire Pressure

WARNING! Equal tire pressure should
be maintained at all times. Never exceed
the maximum inflation pressure shown
on the sidewall of the tire.
The recommended operating tire pressure is:
• Approximately 10 psi for the rear tires
• Approximately 14 psi for the front tires
IMPORTANT: Refer to the tire sidewall for exact
tire manufacturer's recommended or maximum
psi. Do not overinflate. Uneven tire pressure
could cause the cutting deck to mow unevenly.
(c)
(d)
(f)
(e)
(g)
Figure 2-8
Gas and Oil Fill-up
The gasoline tank is located under the hood. Do
not overfill.
WARNING! Use extreme care when
handling gasoline. Gasoline is
extremely flammable and the vapors
are explosive. Never fuel machine
indoors or while the engine is hot or
running. Extinguish cigarettes, cigars,
pipes, and other sources of ignition.
Service the engine with gasoline and oil as
instructed in the separate Engine Operator/
Owner Manual packed with your tractor. Read
the instructions carefully.
IMPORTANT: Your tractor is shipped with
motor oil in the engine. However, you MUST
check the oil level before operating. Be careful
not to overfill.
IMPORTANT: It is important to NOT top off
your fuel tank when filling with fuel. Leave an
expansion area available inside the fuel tank
to allow for the fuel to expand and for proper
ventilation. Otherwise the unit may not run
properly. Fill the tank in accordance with Figure
2-9 or 2-10.
Figure 2-9-Hydrostatic Models
Figure 2-10-Foot Control CVT Models
IMPORTANT: Do not overfill the tank. Fill
tank to no more than 1⁄2" below bottom
of filler neck to allow spacet for fuel
expansion. See Figure 2-9 and 2-10.
S 2 — A & S
ection SSembly et
-U 9
p