Residual Risks; Commissioning - Scheppach HM80L Traduction Des Instructions D'origine

Protect yourself and you environment from ac-
cidents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If the mitre saw is not used for an extended period
of time, the batteries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representa-
tive.
Safety instructions for handling batteries
Always make sure that the batteries are inserted
1
with the correct polarity (+ and –), as indicated
on the battery.
Do not short-circuit batteries.
2
Do not charge non-rechargeable batteries.
3
4 Do not overcharge batteries!
Do not mix old and new batteries or batteries
5
of different types or manufacturers! Replace an
entire set of batteries at the same time.
6 Immediately remove used batteries from the de-
vice and dispose of them properly! Do not dis-
pose batteries with household waste. Defective
or used batteries must be recycled according to
Directive 2006/66 / EC. Give back batteries and
/ or the device has been offered to the collective
facilities. About disposal facilities you can inform
by your municipal or city government.
7 Do not allow batteries to heat up!
8 Do not weld or solder directly on batteries!
Do not dismantle batteries!
9
Do not allow batteries to deform!
10
Do not throw batteries into fire!
11
12 Keep batteries out of the reach of children.
13 Do not allow children to replace batteries without
supervision!
Do not keep batteries near fire, ovens or other
14
sources of heat. Do not use batteries in direct
sunlight or store them in vehicles in hot weather.
Keep unused batteries in the original packaging
15
and keep them away from metal objects. Do not
mix unpacked batteries or toss them together!
This can lead to a short-circuit of the battery
and thus damage, burns or even the risk of fire.
Remove batteries from the equipment when it
16
will not be used for an extended period of time,
unless it is for emergencies!
24 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
17 NEVER handle batteries that have leaked with-
out appropriate protection. If the leaked fluid
comes into contact with your skin, the skin in
this area should be rinsed off under running wa-
ter immediately. Always prevent the fluid from
coming into contact with the eyes and mouth.
In the event of contact, please seek immediate
medical attention.
18 Clean the battery contacts and corresponding
contacts in the device prior to inserting the bat-
teries.
m Residual risks
The machine has been built according to the
state of the art and the recognised technical
safety requirements. However, individual residu-
al risks can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the op-
erating button may not be pressed when inserting
the plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your mitre saw provides optimal per-
formance.
• Hands may never enter the processing zone when
the machine is in operation.
• Release the handle button and switch off the ma-
chine prior to any operations.

Commissioning

Prior to commissioning, observe the safety in-
structions in the operating instructions.
REMOVAL FROM THE PACKAGING
Remove the machine from its package, which pro-
tects it during transport, without damaging the pack-
age in order to be able to use it later for transporting
the mitre saw for long-term storage.