GE Caliber Serie Manuel Du Propriétaire page 5

Remote Control Features and Settings
11. Louver SIDE/SIDE Button (select models)
Press the LOUVER SIDE/SIDE button to choose the
position of the vertical airflow louvers.
Status display of air flow
COOL/DRY/HEAT/FAN
NOTE:
• When humidity levels are high, condensate water may
occur at the air outlet if all vertical louvers are adjusted to
far left or right.
• When turning the unit on, the remote control will
automatically return the louver to the previous set position.
12. SLEEP Button
1. Operation in COOL or DRY modes: One hour after
SLEEP mode starts, the temperature will rise 2°F above
set temperature. After another hour, the temperature rises
additional 2°F. The unit will run for additional six hours
before it turns off. The final temperature is 4°F higher
than initial set temperature. Using this feature helps with
achieving maximum efficiency and comfort from your unit
while you sleep.
2. Operation in Heat Mode: One hour after SLEEP mode
starts, the temperature will decrease 4°F below set
temperature. After another hour, the temperature will
decrease an additional 4°F. After an additional three
hours, the temperature will rise by 2°F. The unit will run
for an additional three hours before it turns off. The final
temperature is 6°F lower than the initial set temperature.
Using this feature will help with achieving maximum
efficiency and comfort from your unit while you sleep.
3. In AUTO mode, the unit operates in corresponding sleep
mode adapted to the automatically selected operation mode.
NOTE:
• When the unit is set to sleep mode, the fan speed will be
set to low speed and cannot be changed.
• When the TIMER function is set the sleeping function
cannot be set. If the sleeping function has been set and
the user sets the TIMER function, the sleeping function will
be canceled and the unit will be set to the timer function.
13. Fahrenheit/Celcius Button
49-5000277 Rev. 0
Press F/C to toggle remote and unit display temperature
between Fahrenheit and Celsius.
14. EXTRA FUNCTION Button
Press the EXTRA FUNCTION button to view all other
operations. Press CONFIRM/CANCEL to select and
save the chosen operation. If no button is pressed for 10
seconds, the remote will exit EXTRA FUNCTION mode.
A) Refresh air - Feature not available on this series.
B) A-B selection - This will allow you to control two
separate units with a single remote control. Note: This
feature would be setup at the time of installation by the
contractor.
C) Auto mode - The heat pump will automatically
select Cool, Heat, or Fan operation according to set
temperature. When FAN is set to AUTO the heat pump
automatically adjusts the fan speed according to room
temperature.
D) Upper and Lower louver lock.
1. Upper louver lock
the top position. Commonly used during cooling.
2. Lower louver lock
the lower position. Commonly used during heating.
3. To unlock the louver press EXTRA FUNCTION button
until either a single louver icon
Note: When the louver is locked, the position cannot be
changed with the LOUVER UP/DOWN button.
E) Timer ON/OFF: Sets a countdown timer until the
unit is turned ON/OFF. TEMP+/TEMP- button is
pressed with the length of time increment/decrement
in 0.5 hour between 0-12 hours,and 1 hour increment/
decrement between 12-24 hours.
1. When the remote is set to ON, the system will turn
off until the countdown timer ends. Then the indoor
unit will turn on and operate in mode, temperature
setting and fan speed that was displayed when timer
was set.
2. When the remote is set to OFF, the system will
remain ON until the countdown timer ends.
F) 48°F Heating sets the system to maintain 48°F. This
is used to prevent freezing during long unoccupied
periods of time.
15. Confirm/Cancel Button
Saves and exits the EXTRA FUNCTION selection.
16. HEALTH Button
Feature is not Available
17. LOCK Button
Used to lock buttons and LCD display.
will lock the horizontal louver in
will lock the horizontal louver in
or oscillate icon .
5