To delay the start
1. Close the door.
2. Repeatedly press
until you see the desired hours of delay in the display.
When the delay reaches 12 hours, the delay turns off. Press
Delay Start again to select a new number of delay hours.
3. Select a wash cycle and options.
NOTE: To cancel the delay and cycle, press Cancel. To cancel
the delay and start the cycle immediately, press Delay Start until
no hours show in the display.
Delay Start (models with 2-4-8 hour button)
Use Delay Start to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown. After adding items, close the door firmly until it
latches. The delay countdown will not continue if the door is not
latched.
To delay the start
1. Close the door.
2. Press Delay Start 1 time for a 2-hour delay, 2 times for a 4-
hour delay, or 3 times for an 8-hour delay.
3. Select a wash cycle and option.
The number glows below Hours. The dishwasher starts the cycle
in the selected number of hours. If you do not press a cycle
within 30 seconds, the Delay Start indicator turns off.
NOTES:
To cancel the delay and cycle, press Cancel.
To cancel the delay and start the cycle, press Delay Start until
"8" glows. Then press Delay Start one more time. The delay
turns off and the delayed cycle starts.
Cycle Status Indicators
Follow the progress of your dishwasher with the Cycle Status
indicators.
NOTE: Your model may have some or all of the indicators shown
above.
Sensing/Soaking
Sensing/Soaking glows during both the Sensing and Soaking
parts of the cycle. Your dishwasher senses soil level during soil
sensing intervals and water temperature during Water Heating
pause intervals. Your dishwasher soaks when Soak & Scrub is
selected. Washing continues while Sensing occurs. Washing
pauses for regular intervals during a soak.
16
Water Heating
Water Heating glows only when the cycle pauses to heat water to
a set temperature. Washing or rinsing continues as water heats.
Once water reaches the set temperature, the light goes off and
the cycle resumes.
NOTE: Some portions of the cycle are heated for fixed periods of
time, but not to a set temperature. The cycle does not pause. The
Water Heating light is not turned on for these timed heats.
Clean
Clean glows when a cycle is finished. The light turns off when you
open and close the door or press Cancel.
Sanitized
If you select the SANI RINSE™ option, Sanitized glows when the
SANI RINSE cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted. The light goes off when
you open the door.
Refill Rinse Aid
Fill the Rinse Aid dispenser when Refill Rinse Aid is lit. A rinse aid
prevents water from forming droplets that can dry as spots or
streaks.
If the Rinse Aid dispenser is empty, the light glows when you
select a cycle or while a cycle is running.
Active Vent
The Active Vent reduces the sounds from your dishwasher. The
cover closes after the cycle starts. Filling and washing sounds are
reduced. The Active Vent opens when wash action ends and
vapor is vented into room.
NOTE: There is a slight noise when the cover closes or opens.
This is normal.
Drying System
During drying, you can see steam escaping through the vent at
the upper left corner of the door. This is normal as the heat dries
your dishes.
IMPORTANT: The vapor is hot. Do not touch the vent
during drying.
Overfill Protection Float
The overfill protection float (in the front right corner of the
dishwasher tub) keeps the dishwasher from overfilling. It must be
in place for the dishwasher to operate.
Check under the float for objects that may keep the protector
from moving up or down.