POLTI MOPPY Manuel D'instructions page 13

The red power indicator light will come on
(14) ( ). After a few seconds Moppy is
ready.
2. FLOOR CLEANING AND SANITI-
SING
Use the product on surfaces previously swept
or vacuumed.
Ensure that steps in Chapter 1 have been fol-
lowed.
2.1 Attach the microfiber cloth supplied to the
brush. To make it easier to attach, the cloth
has an easy lock/release system to avoid ben-
ding over and using your hands. Just place
the cleaning side of the cloth on the floor and
rest the brush on top of it (15-16).
2.2 Place the brush with cloth over the base,
aligning the arrow of the brush with the arrow
of the base (18). Misalignment of the arrows
prevents Moppy from functioning.
2.3 When the brush is properly resting on the
base, the base will start delivering steam onto
the floor cloth. Steam delivery is signalled by
the flashing red indicator light (14).
The green indicator light (
on after about 20 sec. indicating that the
cloth has been sanitised. The delivery of
steam can be extended to further dampen
the cloth.
The first time it is used, we recommend lea-
ving it on the base for another few seconds in
order to steam the cloth evenly.
2.4 Clean floors by moving the brush over the
surface to be treated.
When the cloth appears to be dry, return it to
the base and steam the cloth.
The indicator light (
ter about 20 sec. indicating that the cloth has
been sanitized.
You can also keep it longer if you want to
soak the cloth more. For particularly porous
or rough floors, it is recommended to extend
the steaming step so the cloth reaches the
correct level of dampness.
2.5 When cleaning the floor, if the cloth is
very dirty, you can remove it and replace it
with a clean cloth and continue the cleaning
operations.
2.6 Standby parking: you can place the brush
on the base without activating steam delivery
during cleaning operations; place the brush
with the side of the arrow facing outwards
(20) and insert the telescopic tube from the
handle of the base into the lock (23).
) (19) will come
) (19) will come on af-
Wait for the cloth to cool before removing it
from the brush. To do so, rest a foot on the
corresponding symbol on the tab of the
cloth and pull the brush upward (17) .
WARNING: Do not use the brush without the
cloth.
WARNING: Moving the brush away from the
base switches off delivery. For additional sa-
fety, the steam delivery switches itself off af-
ter 60 seconds and Moppy enters auto-lock
mode. To resume delivery, detach the brush
from its base, wait 15 seconds for reset and
then place the brush back on the base and
proceed as per point 2.2.
WARNING: For delicate surfaces, perform a
cleaning test on a hidden part, let it dry and
ensure that no changes in colour or deforma-
tions have occurred.
3. CLEANING VERTICAL SURFACES
Moppy can clean and sanitise all vertical wa-
shable surfaces, such as walls with tiles, mar-
ble coverings, shower interiors, cabinet doors,
etc.
3.1 Attach a clean microfibre cloth to the bru-
sh, then steam the cloth as described in point
2.2 - 2.3.
3.2 When the cloth is ready, clean the surface
to be treated and return to the base to steam
the cloth again whenever necessary.
4. DUST CATCHING FUNCTION
Before using Moppy on delicate surfaces
check that there are no foreign objects
between the cloth and the surface that may
cause scratches .
4.1 To remove dust from the surfaces, attach
the dry microfiber cloth to the brush as per
point 2.1, then attach the electrostatic cloth:
place the cloth on the floor and rest the brush
on top of it, then secure the electrostatic
cloth by hooking it in the buttons on the top
of the brush (21-22).
4.2 Dust the floors by moving the brush.
4.3 After cleaning, remove the electrostatic
cloth and dispose of it appropriately.
Moppy is compatible with the XXL electrosta-
tic cloths commonly found on the market.
5. OUT OF WATER
The water level is always visible thanks to the
see through tank.
When the water inside the tank has been used
| 13 |