Master TERA Manuel D'utilisation Et D'entretien page 14

07. HOW TO MEMORIZE/DELETE A RADIO DEVICE
07.1 USING A TRANSMITTER
01. Bring the motor in an intermediate position.
02. Press PROG of an already memorized transmitter for 5 s. The motor performs 2
upward movements.
03. Within 15 seconds, to memorize/delete:
a transmitter: press STOP of transmitter you want to memorize/delete
a rain sensor: press «P2» of rain sensor you want to memorize/delete
04. 1 upward movement: device memorized!!
1 downward movement: device deleted!!
2 downward movement: error!!
NOTE:
point 04. "error"is reported if the radio code is not received in time or if the receiver's memory is full or if you try to delete the only memorized transmitter,
07.2 USING COMMAND BUTTONS
01. Bring the motor in an intermediate position.
02. Within 15 seconds, press UP 8 times (briefly and quickly).
The motor performs 3 upward movements.
03. Within 15 seconds, press UP 3 times (briefly and quickly).
The motor performs 2 upward movements.
04. Within 15 seconds, to memorize/delete:
a transmitter: press STOP of transmitter you want to memorize/delete
a rain sensor: press «P2» of rain sensor you want to memorize/delete
05. 1 upward movement: device memorized!!
1 downward movement: device deleted!!
2 downward movement: error!!
NOTE:
point 06. "error"is reported if the radio code is not received in time, if the receiver's memory is full; with this procedure you can delete the only memorized transmitter
08. FINE ADJUSTMENT OF UPPER LIMIT SWITCH
WARNING:
The modification of the upper limit switch is not possible if the upper limit switch has been learned by contact with an obstacle.
01. Bring the motor to the upper limit switch (or near).
02. Press in sequence the STOP - PROG - UP buttons(*).
The motor makes 1 downward movement.
03. Using UP and DOWN adjust the upper limit switch.
04. Press PROG. The motor makes 1 down/up movement.
(*) briefly press, max 2 seconds between each press and the next.
09. FINE ADJUSTMENT OF LOWER LIMIT SWITCH
WARNING:
The modification of the lower limit switch is not possible if the lower limit switch has been learned by contact with an obstacle.
01. Bring the motor to the lower limit switch (or near).
02. Press in sequence the STOP - PROG - DOWN buttons(*).
The motor makes 1 downward movement.
03. Using UP and DOWN adjust the upper limit switch.
04. Press PROG. The motor makes 1 up/down movement.
(*) briefly press, max 2 seconds between each press and the next.
10. MODIFY BOTH THE LIMIT SWITCHES
WARNING:
If the procedure is not completed, the motor automatically sets a short stroke. In case of interruption of the procedure it is necessary to repeat it completely.
01. Bring the motor in an intermediate position.
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Press in sequence the STOP - PROG - STOP buttons(*).
The motor makes 1 up/down movement; motor moves downward.
04. Depending on how the roller shutter is installed, follow the instructions at point 5
and following of the paragraphs 06.1 or 06.2 or 06.3 or 06.4
(*) briefly press, max 2 seconds between each press and the next.
11. FAVORITE POSITION
11.1 USING A TRANSMITTER
ARCO
To memorize:
01. Bring motor in the favorite position
02. Press together STOP and FOR ME
until the motor performs a signal.
To recall:
01. Press FOR ME
11.2 USING THE COMMAND BUTTONS
To memorize:
01. Bring the motor in the favorite position.
02. Press DOWN 6 times (briefly and quickly).
To recall:
01. Press DOWN 2 times (briefly and quickly).
FLUTE, KUADRO, KORT
To memorize:
01. Bring motor in the favorite position
02. Press briefly STOP 6 times and then
hold DOWN until the motor performs
a signal.
To recall:
01. Press STOP 3 times (briefly)
TO MEMORIZE
6 x DOWN
PROG
(5 seconds)
8 x UP
PROG
STOP
PROG DOWN
STOP
ON
VISIO
To memorize:
01. Bring motor in the favorite position
02. Press together STOP and
the motor performs a signal
To recall:
01. Press FOR ME
06
STOP
STOP
3 x UP
UP
PROG STOP
STOP
Other transmitters...
until Consult the manual of your transmitter in
the section about the functions
associated with the buttons.
TO RECALL
2 x DOWN
P2
P2
P2
P2
PROG
PROG
Go to point 5
and following of
the paragraphs
06.1 or 06.2 or
06.3 or 06.4