Parts List - Let's Go Aero GearDeck H00604 Manuel Du Produit

PARTS LIST

QTY. DESCRIPTION
A 1 TWINTUBE SPINE
B 2 RETAINER CLIP
5/8" SILENT HITCH PIN ®
C 1
D 1 5/8" SILENT HITCH PIN WITH HANDLE
E 1 5/8" LOCK WASHER
F
1 5/8" FLAT WASHER
G 1 5/8" PLASTIC BUSHING
H 2 5/8" SPRING NUT
K 1 WAX
L 2 RUBBER BUMPER
M 2 SLIDE TUBES
N 2 WING TRACK
P 4 HAT BRACKETS
Q 8 5/16" X 1" CARRIAGE BOLTS
R 1 SAFETY CABLE (W/ QUICK LINK)
S 2 REFLECTOR END CAPS, 2 1/4"
T 8 5/16" WASHERS
U 8 5/16" NYLOCK NUTS
V 1 TRAY
W 10 1/4-20 HEX BOLTS
X 8 1/4-20 NYLOCK NUTS
Y 8 1/4" FLAT WASHER
Z 8 1/4" X 1 1/4" FENDER WASHER
STEP 1
Remove Spring Nuts [H] from Silent Hitch
Pins and install two Spring Nuts into the
TwinTube Spine [A] as shown. [Fg.1-3]
The TwinTube [A] shank
end contains two mounting
holes. [Fg.2] Use the second
hole in from the end. If more
clearance is needed, you
may use the first hole in from
the end.
STEP 2
REQUIRED TOOL: 7/8" WRENCH
Slide the TwinTube [A] shank into the
receiver with the 5 inch rise positioned
above the hitch as shown. Align the
mounting hole with Spring Nut [H] and
the receiver hitch. [Fg.4]
Insert the Silent Hitch Pin [C] with a
5/8in Lock Washer [E] & 5/8in Flat
Washer [F] into the receiver hole and
thread through the Spring Nut [H]. Tighten firmly with wrench and
secure with Retainer Clip [B]. [Fg. 5]
PARTS
H A
1ST HOLE
2ND HOLE
POSITION WITH
RISE AS SHOWN
[Fg. 4]
QTY. DESCRIPTION
AA 4
BB 1
CC 1
DD 1
EE 4
FF
4
GG 4
HH 4
JJ 4
KK 8
LL 6
MM 2
NN 8
PP 2
QQ 2
RR 2
SS 1
TT 1
UU 2
VV 2
WW 4
XX 4
YY 4
H
[Fg. 2]
THIS END INTO
VEHICLE
HITCH RECEIVER
A
[Fg. 5]
Page 2 of 19
PARTS
DRAIN PLUGS
FIXED LID
PIVOT LID (W/ LOGO)
HANDLE
1/4-20 X1" BUTTON-HEAD CAP BOLTS
1/4 X 1" FENDER WASHER
1/4" FLAT WASHER
1/4-20 LOCK WASHER
1/4-20 WELD NUT
10X24-1 PHILLIPS PAN SCREW
#10 WASHER
3/16 X 1 FENDER WASHER
10-24 NYLOCK NUT
RUBBER LATCH
ANGLES
LATCH KEEPER
LED LIGHTS
LED LICENSE PLATE BRACKET
LED MOUNT BRACKET
HEX BOLT
NYLOCK NUT
FLAT WASHER
K-LATH TEX SCREWS
A
A
F
H
E
B
[Fg. 3]
H
H
[Fg. 1]
C
A