Drill Safety Warnings; Functional Description - Makita DA4000LR Manuel D'instructions

ENGLISH
(Original instructions)
1 Switch trigger
2 Reversing switch lever
3 High
4 Low
5 Chuck key
6 Drill chuck
7 Hex wrench
SPECIFICATIONS
Model
Capacities
Steel ................................................................... 13 mm
Wood ................................................................. 38 mm
–1
No load speed (min )
High ................................................................... 0 – 900
Low.................................................................... 0 – 400
Overall length ..................................................... 413 mm
Net weight ............................................................. 4.0 kg
Safety class ............................................................
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
This tool is intended for drilling in wood, metal and plas-
tic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

DRILL SAFETY WARNINGS

1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
4
Explanation of general view
8 Loosen
9 Angle housing
10 Joint
11 Socket
12 Bolt
13 Spindle
14 Two faces
7.
DA4000LR
8.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
/II
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
''OFF'' position when released.
GEA010-1
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
Reversing switch action (Fig. 2)
This tool has a reversing switch to change the rotational
direction. Move the reversing switch lever to the "A" side
for clockwise (forward) rotation or the position "B" side for
counterclockwise (reverse) rotation.
CAUTION:
• Always check the rotational direction before operation.
• Use the reversing switch only after the tool comes to a
GEB001-6
complete stop. It will damage the tool to change the
rotational direction before the tool stops.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing side grip (auxiliary handle)
CAUTION:
• Always use the side grip and hold it with both hands to
ensure operating safety.
15 For higher speed operation
16 Tighten
17 Limit mark
18 Brush holder cap
19 Screwdriver
Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.