Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
MODEL: P
50
LSLW
TOOL USE AND CARE
●
Know this tool.
Read manual carefully, learn
its applications and limitations, as well as the
specific potential hazards related to this tool.
●
Use only fasteners that are recommended
for your models.
Do not use the wrong
fasteners or load the fasteners incorrectly.
●
Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tool's
operation.
If damaged, have the tool serviced
before using. Many accidents are caused by
poorly maintained tools.
●
Maintain tools with care.
Keep tool clean. A
properly maintained tool, reduces the risk of
binding and is easier to control.
●
Store tools out of the reach of children and
other untrained people.
Tools are dangerous
in the hands of untrained users.
●
Check operation of the tool before use.
Do not force tool.
Use the correct tool for your
●
application. The correct tool will do the job better
and safer at the rate for which it is designed.
●
Use clamps or another practical way to
secure and support the workpiece to a
stable platform.
Holding a tool by hand or
against the body is unstable and may lead to
loss of control.
●
Keep the tool and its handle dry, clean and
free from oil and grease.
Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any
strong solvents to clean your tool.
●
Do not use the tool as a hammer.
Never use this tool in a manner that could
●
cause a fastener to be directed toward
anything other than the workpiece.
●
Always carry the tool by the handle. Never
carry the tool by the air hose.
●
Do not use the tool if it leaks air or does not
function properly.
Do not operate the tool if it does not contain
●
a legible warning label.
04
.
HTTP://WWW FREEMANTOOLS COM
TOOL SERVICE
●
Use only accessories that are identified by
the manufacturer for the specific tool model.
●
Use of unauthorized parts or failure to
follow maintenance instructions may create
a risk of injury.
●
Use only the lubricants supplied with the
tool or specified by the manufacturer.
●
Tool service must be performed only by
qualified repair personnel.
OPERATION
●
Do not drive fasteners near edge of material.
The workpiece may split causing the fastener or
ricochet, injuring you or people around.
●
Do not drive fasteners on top of other
fasteners or with the tool at an overly steep
angle as this may cause deflection of
fasteners which could cause injury.
Do not actuate the tool unless you intend to
●
drive a fastener into the workpiece.
●
Always handle the tool with care:
◆Respect the tool as a working implement.
◆
Never engage in horseplay.
◆Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
●
The connector on the tool must not hold
pressure when air supply is disconnected.
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line is
disconnected, possibly causing injury.
●
Do not use oxygen, combustible gases or
bottled gasses as a power source for this tool.
Explosion may occur, causing injury or death.
●
Do not connect with an air compressor
which can potentially exceed 200 Psi.
As tool may burst, possibly causing injury.
●
Always disconnect air source:
Before unloading or making adjustments.
When maintaining the tool.
When clearing a jam.
When touching the safety yoke.
When tool is not in use.
When moving to a different work area.
Such precautionary measures reduce the risk of
injury to persons.
.
1-888-669-5672
MODEL: P
50
LSLW
LOADING TOOL
●
Do not load the tool with fasteners when
any one of the operating controls is
activated.
●
Never place a hand or any part of body in
fastener discharge area of tool.
●
Never point tool at anyone.
WARNING:
!
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
UNPACKING
●
This tool has been shipped completely
assembled.
●
Make sure that all items listed in the packing
list are included.
Carefully remove the tool and any
●
accessories from the box.
Inspect the tool carefully to make sure no
●
breakage or damage occurred during
shipping.
Do not discard the packing material until you
●
have carefully inspected and satisfactorily
If
operated the tool.
●
If any parts are damaged or missing, please
call 1-888-669-5672.
PACKING LIST
●
2 In 1 flooring nailer
●
Color box
●
Mallet
●
Air connector(Pre-installed)
●
Adjustment tools
●
Lubrication oil
●
Anti-dust cap
(Pre-installed)
●
5/8" ot plate
fo
Instruction manual
●
WARNING:
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
HTTP://WWW FREEMANTOOLS COM
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
FEATURES
SPECIFICATIONS
Operation pressure:
70-115 psi
Nails capacity:
L: 100 pcs
U 9
: 0 pcs
Tool weight:
9.08 lbs
Air inlet:
1/4" NPT
Fasteners:
7.5mm (3/10")
38mm
1-1/2"
38mm
45mm
1-3/4"
45mm
50mm
2"
50mm
(15.5Ga.Staples)
(16Ga.L cleats)
Compatible With Generic Brands Of 15.5Ga
Staples & 16Ga. L-Cleats.
FEATURES
●
REVOLUTIONARY 2 IN 1 DESIGN
For use with Staples, L-Cleats.
●
NO-MAR DESIGN
Provides increased protection from marring
when working with a finished flooring surface.
●
ANODIZED ALUMINUM MAGAZINE
For long lasting durability.
●
DURABLE CONSTRUCTION
Light weight and durably constructed of high-
strength aluminum and heat treated steel parts.
●
AIR FILTER
Keeps interior components debris free,
extending tool life.
●
MALLET INCLUDED
.
.
1-888-669-5672
12.7mm (1/2")
1-1/2"
1-3/4"
2"
05
Publicité
Table des Matières
