Manuels Connexes pour Granberg 6303H
Sommaire des Matières pour Granberg 6303H
- Page 1 Dok. Nr: M6303-ETL V: 1.0 2022-03-29 Installation Instructions / Instructions d’installation Baselift Corner 6303H / 6303L 6303H 6303L 1,6” 4.1” WWW: Baselift Corner 6303...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS / PRESCRIPTIONS DE SÉCURITÉ IMPORTANTES EN When using an electrical furnishing, basic precautions should always be followed, including the following: Read all instructions before using the BASELIFT. DANGER - To reduce the risk of electric shock: 1. Always unplug this furnishing from the electrical outlet before cleaning. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: 1.
- Page 3 Technical data / Données techniques EN Thank you for choosing to install a product from Granberg! In order for the product to work safely and securely, it is extremely essential that the installation instructions be followed. The installer should read and understand all the installation instructions before installation begins.
- Page 4 Planning / Planification EN Very Important! Check floor stability before installation. Maximum load on lifting unit is 220 lb (100kg) and dead load up to 220 lb (100kg). Ensure that the wall can withstand the concentrated load that occurs under motor units. Make sure that the motor units can be fixed to the wall and that the structure is not porous.
- Page 5 Electricity and Water / Électricité et eau EN The lifting unit requires two power outlets and consumes a maximum of 10 A (5 A+5 A). (mm) If the counter has a sink, the connections for electricity, water and drain should be placed centrally below the mixer. The electrical connection can also be placed in a protected position inside a motor unit.
- Page 6 Content of delivery / Contenu de la livraison 2x M8X45 2x M8 16 mm 6x M8x16mm Accessories / Accessoires 16 mm 48x 3x12 mm 16 mm 24x 3x16 mm 8x M6x12...
- Page 8 18.9“ LEFT (L) 18.9“ RIGHT (R) A: 4.92“ B: 6.89“ C: 19.29“ D: 21.26“...
- Page 9 18.9” Right Right Left Left...
- Page 10 Niveleur Niveleur...
- Page 11 16 mm 6x M8x16mm...
- Page 15 22” - 23.2” (560 - 590)
- Page 16 13mm 10 mm 2x M8X45 2x M8...
- Page 19 230V WARNING – Ensure both power supply cords are connected before use AVERTISSEMENT – Avant utilisation, assurez-vous que les deux cordons d'alimentation sont branchés...
- Page 20 Wooden front / Façade en bois B - 0.157” (4mm) 2.36” (60mm) 0.787 (20mm) > 4” > 2.3” 0.866” (22mm) 1.42” (36mm) For drawer Pour tiroir DWG NO. REVISION Granberg Interior AB 10433 Tel. +46(0)11197750 info@granberg.se TITLE: www.granberg.se Frontfästen DWG NO. REVISION DRAWN MATERIAL: FINISH:...
- Page 21 min 0.2” (5 mm) min 0.2” (5 mm)
- Page 24 8x M6x12 HEX 1/8”...
- Page 25 16 mm 16 mm 6x 3 x 16 mm 22x 3 x 12 mm 17.6” (447mm) 16 mm 16 mm 3x- 3 x 16 mm 3x- 3 x 16 mm DRAWN CHECKED UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS TOLERANCES: LINEAR: SS-ISO 2768-m ANGULAR: SS-ISO 2768-m DEBUR AND BREAK SHARP EDGES DO NOT SCALE DRAWING...
- Page 26 16 mm 12x 3 x 16 mm 1400 L - 0.39” (10 mm) / R - 0.39” (10 mm) 1x L + 1x R 565 - 590 DRAWN CHECKED UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS TOLERANCES: LINEAR: SS-ISO 2768-m ANGULAR: SS-ISO 2768-m DEBUR AND BREAK SHARP EDGES DO NOT SCALE DRAWING DRAWN...
- Page 27 16 mm 8x 3 x 12 mm 0.315“ 8 mm...
- Page 28 16 mm 16x 3 x 12 mm 17” (431mm) 17” (431mm) 0.98” (25mm) 13” (330mm) 13” (330mm) 0.98” (25mm) 0.315” 0.315” (8mm) (8mm) DRAWN CHECKED NLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS TOLERANCES: LINEAR: SS-ISO 2768-m ANGULAR: SS-ISO 2768-m DEBUR AND BREAK SHARP EDGES DO NOT SCALE DRAWING...
- Page 29 1x L + 1x R 565 - 590 DRAWN CHECKED UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERS TOLERANCES: LINEAR: SS-ISO 2768-m ANGULAR: SS-ISO 2768-m DEBUR AND BREAK SHARP EDGES DO NOT SCALE DRAWING Granberg Tel. +46(0)11 info@granbe www.granb DRAWN MATERIAL: CHECKED WEIGHT:...
- Page 30 16 mm 8x 3 x 12 mm...
- Page 31 Adjustment / Ajustement Leveler Wasserwaage...
- Page 32 Adjustment / Ajustement 9/16”...
-
Page 33: Functional Tests
Functional tests Complete functional tests should be carried out after installation: Ensure both power supply cords are connected before use! Test run the lift unit up and down all the way to each end position. Make sure that the lift runs freely without obstacles, risk of pinching and noise. - Page 34 Before you use the device - Read the users manual Only authorized persons may use the this product! Authorization means obligation to read and follow the instructions. It is very important that you read and understands the users manual before you use the device. The user manual is attached as a separate booklet.
- Page 36 Granberg Interior AB Box 6112 600 06, Norrköping Tel: 011-19 77 50 E-mail: info@granberg.se Internet: www.granberg.se...