Publicité
Cordless drill/driver
Max. torque, hard/soft
screwdriving application ac-
cording to ISO 5393
Max. drilling diameter (first/second gear)
– Steel
– Wood
Max. screw diameter
Tool holder
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation
– during storage
Recommended batteries
Recommended chargers
– PBA 18 V....V-.
– PBA 18 V....W-.
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-1.
Typically the A-weighted noise level of the power tool is less
than 70 dB(A). Uncertainty K = 5 dB. The noise level when
working can exceed 80 dB(A).
Wear hearing protection
Total vibration values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1
2
Drilling in metal: a
= 1.3 m/s
, K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
Bosch Power Tools
To estimate vibration and noise emissions accurately, the
UniversalDrill 18
times when the tool is switched off or when it is running but
mm
30/18
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
mm
10
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
mm
30
and organising workflows correctly.
mm
8
mm
10
Assembly
A)
kg
1.2–1.5
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
°C
0 to +45
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
°C
-15 to +50
°C
-20 to +70
Charging the Battery
PBA 18 V...V-.
Use only the chargers listed on the accessories page.
u
PBA 18 V...W-.
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
AL 22.. CV
Note: The battery is supplied partially charged. To ensure
AL 1810 CV
full battery capacity, fully charge the battery in the charger
AL 1815 CV
before using your power tool for the first time.
AL 1830 CV
The lithium-ion battery can be charged at any time without
AL 1880 CV
reducing its service life. Interrupting the charging process
AL 1810 CV
does not damage the battery.
AL 1815 CV
The lithium-ion battery is protected against deep discharge
AL 1830 CV
by the "Electronic Cell Protection (ECP)". When the battery
AL 1880 CV
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Removing the battery
2
.
To remove the battery (6), press the battery release but-
ton (5) and pull the battery to the rear and out of the power
tool. Do not use force to do this.
Changing the tool (see figure A)
The drill spindle is locked when the on/off switch (8) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
English | 13
1 609 92A 4XS | (22.02.2019)
Publicité
