Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
K-50 Drain Cleaning Machine
Description, Specifications and
Standard Equipment
Description
The RIDGID K-50 is a portable Drain Cleaning Machine
" to 4" drain lines. Applications in-
designed to clean 1
1
/
4
clude sink, shower and floor drains. Capable of running
three different size cables:
The machine is driven by a 1/6 HP motor that has a
grounded electrical system. An integral Ground Fault In-
terrupter (GFCI) is built into the line cord. A toggle switch
provides FORWARD/OFF/REVERSE control of the motor.
The K-50 is designed to use
cable that has a quick change coupling system for dis-
connecting tools. The cable is manually fed in and out of
the drain and rotates at a speed of 400 RPM. The rotation
of the cable is controlled by a clutch handle. The cable
stops instantly when the clutch handle is released.
The K-50 is also designed to use with the A-17 Adapters.
" or
Adapters will hold
5
/
16
Rotation of the adapters is controlled by the clutch handle.
The cable adapter is equipped with a quick-acting brake
which immediately stops rotation of the drum when the
clutch handle is pulled upward.
Specifications
Line Capacity ...............Depends on choice of cable.
Refer to the following chart for
recommendations.
Recommended Line Size and Reach
Cable Size
Line Size
" Cable
" - 1"
5
/
3
/
16
4
" Cable
3
/
1
1
/
8
4
" (C-8)
5
/
1
1
/
8
4
" (C-9)
5
/
2" - 4"
8
Cable Sizes ..................
5
/
Motor
Type ..............................115V/50-60 Hz, Reversible,
230V Available Upon Request
Rating ............................
1
/
Amps .............................4
Weight...........................37.5 lbs. (17 kgs.)
Dimensions
Length ...........................12" (205mm)
Height ............................17.5" (445mm)
Width .............................13" (330mm)
4
",
" and
".
5
/
3
/
5
/
16
8
8
" diameter sectional-type
5
/
8
" continuous length cables.
3
/
8
Reach
25' - 50'
" - 2"
25' - 35'
" - 3"
100'
100'
",
" and
"
3
/
5
/
16
8
8
HP
6
Machine Options
Catalog No.
Model
115V
230V
58920 76455
58960 76475 K-50-4
58980 76485 K-50-6
59000 76495 K-50-8
52972
—
K-50-9
Standard Equipment
Model
No.
Cable
A-30
Six Sections:
" x 7
C-8,
5
/
8
(45', 13.7m)
A-40
Six Sections:
" x 10'
C-9,
5
/
8
(60', 18.3m)
Model
No.
Description
A-17-A
Adapter with 25' x
A-17-B
Adapter with 35' x
Machine Inspection
To prevent serious injury, inspect your Drain
Cleaning Machine. The following inspection pro-
cedures should be performed before each use.
1. Make sure the Drain Cleaning Machine is unplugged
and the directional switch is set to the OFF posi-
tion. (Figure 1)
2. Inspect the power cord, Ground Fault Circuit Inter-
rupter (GFCI) and plug for damage. If the plug has
Ridge Tool Company
No.
Description
K-50
Machine Only
Machine with:
– A-30 Cable Kit
Machine with:
– A-17-A Adapter
– A-30 Cable Kit
Machine with:
– A-17-A Adapter
– A-18-B Adapter
– A-30 Cable Kit
Machine with:
– A-40 Cable Kit
Tools & Accessories
T-201 Straight Auger
' T-202 Bulb Auger
1
/
2
T-205 "C" Cutter
T-211 Spade Cutter
A-13 Coupling Pin Key
A-10 Cable Carrier
A-14-6 Rear Guide Hose
A-1 Left-Hand Mitt
T-206 Funnel Auger
T-215 4-Blade Cutter
T-231 "C" Cutter
A-13 Coupling Pin Key
A-10 Cable Carrier
A-14-610 Rear Guide Hose
A-1 Left-Hand Mitt
" Cable w/Bulb Auger
5
/
16
" Cable w/Bulb Auger
3
/
8
WARNING
Publicité
Chapitres
Table des Matières
