Maintenance / Service - Skil 2900 Notice Originale

corrugated cardboard 6 mm
solid cardboard 2 mm
rose stems 4 mm
WHEN USING SCISSOR HEAD FOR TOUGH
MATERIALS:
vinyl floor-covering 4 mm
corrugated cardboard 6 mm
solid cardboard 2 mm
plastic straps 1.8 mm
plastic sheets (PVC, etc.) 1.25 mm
tin/aluminium sheets 0.4 mm
! do not cut metals other than tin/aluminium sheets
- always test out first on a piece of scrap material
! do not attempt to sharpen the cutting blade
surfaces; replace the scissor head when the
cutting blades are worn or damaged
APPLICATION ADVICE
• For working continuously you may use an additional
interchangeable battery (available as SKIL accessory
2610397159) enabling you to charge one battery while
using the other
• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use
• Keep tool and charger clean
! always remove the battery before cleaning
- do not immerse tool, charger or scissor head in water
- clean tool, charger and scissor head with a damp cloth
(do not use any abrasive or solvent-based cleaners)
- keep slot M u in scissor head connection free of dust
and dirt with a soft brush or dry cloth
- cover cutting blades with protection cap L 2 when
storing the tool
! unplug charger from power source before
cleaning
If the tool/charger should fail despite the care taken in
•
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skil.com)
- in case of a defective charger send both charger and
battery to your dealer or the SKIL service station
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 9 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 73 dB(A) and the sound
power level 84 dB(A) (standard deviation: 3 dB), and
the vibration 3.3 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
The vibration emission level has been measured in
•
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Ciseaux électriques sans fil
INTRODUCTION
• Cet outil est conçu pour découper une multitude de
matériaux et de tissus, ainsi que des fleurs ou des petites
branches; il permet de réaliser des découpes aussi bien
droites que courbes
• Cet outil n'est pas conçu pour un usage professionnel
Cet outil a été conçu uniquement pour un usage
•
domestique
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'outil et conservez-le pour pouvoir vous y
référer ultérieurement 3
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Interrupteur marche/arrêt de verrouillage
B Bouton de changement de tête de découpe
C Tête de découpe pour matériaux mous
D Symbole de matériaux mous
E Tête de découpe pour matériaux résistants
(NON FOURNIE EN STANDARD)
F Symbole de matériaux résistants
G Bouton de retrait de la batterie
H Témoin du chargeur
J Chargeur
K Fiche du chargeur
L Capuchon protecteur de lame
M Rainure du raccord de la tête de découpe (17)
10
2900