Storage And Handling - Saci SSV 3 Manuel D'utilisation Et D'entretien

ï GB ð
SAFETY REGULATIONS
NOTE: Before installation and use of the pump, read
carefully the instructions described below.
This manual contains basic instructions to be observed
during installation, use and maintenance.
This manual must be consulted by the installation
personnel and by all qualified personnel chosen by the
installation manager to follow its operation.
Furthermore, the manual should always be at hand at the
site where the pump is used.
Identification of the codified instructions in this
manual
m
The safety regulations contained in this manual,
whose inobservance may cause physical injury,
are marked by the general danger sign.
c
The safety regulations contained in this manual,
whose inobservance may cause an electric
shock and resulting serious physical injury or
death, are marked by the electrical hazard sign.
Risks deriving from failure to comply with safety
regulations
Failure to comply with safety regulations may cause
physical injury or material damage as well as possible
environmental contamination.
Failure to comply with safety regulations may lead to the
complete loss of warranty rights.
To cite some examples, non-compliance with the said
regulation may cause:
• breakdown of the main functions of the machine or of
the installation,
• compromised maintenance operations,
• physical damage of an electrical, mechanical nature
General Information
This pump has been made according to the most recent
and advanced techniques, in full compliance with current
standards and has been subject to strict quality control.
This manual will help you understand its function and
learn its possible applications.
The user manual contains important recommendations
necessary for correct and economical operation.
The recommendations should be observed in order to
guarantee the reliability, lifespan and to prevent accidents
deriving from improper use.
The pump should not be used outside the limits described
in the technical specifications.
It is necessary to observe the instructions regarding the
nature, density, temperature and volume of the pumped
liquid, rotation speed and direction, pressure and motor
power as well as all the other instructions contained in this
manual or the documentation attached to the contract.
The data plate indicates the model, the main service
specifications and the serial number.
It is important to provide these indications when
requesting repairs, support and spare parts.
The manufacturing company declines all liability in the
case of accidents or damage caused by negligence,
by improper use of the electric pump or by failure to
comply with the instructions described in this manual or
in conditions other than those specified on the data plate.
m
This equipment must not be used by children
or persons with reduced physical, sensory or
mental abilities, or lacking in experience and
expertise, unless supervised or instructed.
m
Children may not use the equipment without
proper adult supervision.
1 PRELIMINARY INSPECTION
1.1 Delivery and packing
The pumps are supplied in their original packing, in which
they should remain until the time of installation.
Check that the packing is free from damage. If the product
appears to be damaged, inform the retailer immediately.
Take care not to bend the pump when the packing has
been removed: this may cause misalignment or damage
to the pump itself.
The pump should not be exposed to unnecessary shocks
or impact.

1.2 Storage and Handling

Storage temperature:
From -20°C to +60°C
Neither the pump nor the motor should be exposed to
sunlight. If the pump has not been packed, it should be
kept in storage vertically, to prevent any misalignment.
During downtime, the pump should be protected from
frost and atmospheric agents.
Handling:
m
Observe the
standards. Risk of crushing. The pump may be
heavy. Use suitable lifting methods and always
wear personal protection equipment.
Before handling the product, check its weight to identify
suitable lifting equipment.
m
I The pump motors supplied with eyebolt should
not be used to handle the whole assembled
electric pump (see fig. 2.D pg. 5).
For handling pumps with motor of up to 4kW, use the
belts wound around the motor as shown in fig. 2.on pg.
For pumps with motor power greater or equal to 5.5kW,
use the belts attached to the two flanges located in the
coupling area between the pump and the motor as shown
in fig. 2.B pg. 5.
current accident prevention