Suntec Wellness Klimatronic DryFix 3000 Instructions D'utilisation page 17

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22
Internal drying
Mode icons
Child lock:
Water tank full:
Humidity level:
Low temperatute:
Ionizer:
Night mode:
Filter application time:
OPERATION INSTRUCTIONS
Starting the unit
1. Plug in the dehumidifier.
2. Press the POWER button.
3. The unit has a memory function: the unit will start after a power interruption with pre-entered settings.
Timer
-
You can set to set the switch-on in the standby mode as follows:
-
In standby mode, press the timer button on the display will blink "88"
-
Press the Timer button again to set the time by the hour (1-24 h).
-
When the set time has expired, the unit will start automatically.
-
You can change the set time later by pressing the timer button again and set the new required switch-on.
-
You can determine the switch-off by operating as described above during the operation of the timer.
Auto-dehumidification
-
The unit always starts with auto dehumidification mode. But you can set this by pressing the mode button.
-
In this mode, the device sets automatically dehumidification degree considering the ambient temperature and
relative humidity. The dehumidification can also be set by operating the dehumidification button (40% / 45% /
50% / 55% / 60% / 65% / 70%)
-
The unit starts when the set of dehumidification is lower than the relative humidity in the room.
High dehumidification
Under this setting, the device operates without considering the relative humidity in the room is dehumidified noted, the
fan runs faster and thus larger volume of air circulates around.
Low dehumidification
Under this setting, the device operates without considering the relative humidity in the room is dehumidified noted, the
fan runs slower and thus smaller volume of air circulates around.
Hint: If among these three modes, the air purification icon (two small trees) flashes on the display, it means that the filter (HEPA or
activated carbon filter) was not removed and that dehumidification runs parallel with air purification. Once the filter is removed, the
filter icon showis "NO".
Fan function
To activate this function, you need to remove the filter. If the filter is still in the unit, thus flash on the display filter
symbol as a reminder. To protect the filter and to prolong its service life, it is recommended to remove the filter.
Hint: If the room humidity is very high, you activate the extra strong dehumidifying function and additionally press the button "Air
Swing". This allows the automatic slats sweeping and thus larger air flow, which reaches every corner of your room and the
humidity level will be reduced faster.
Internal drying
-
The unit has an internal dehumidifying function. This allows keeping the unit dry and mould-free, if it is not
used for a long time.
-
To activate this function, press and hold the button for at least 3 sec.
-
The drying process takes about 1 hour
-
To stop this process press and hold again the drying button, the unit will run with the previous settings. Press
the power button to stop the drying process and to put the device into standby mode.
Blinks when the drying function is activated
Auto dehumidification, high dehumidification, low dehumidification, air
purification, fan.
Hold the MODE button for at least 3 sec. to activate or deactivate the child lock.
Blinks as soon as the water tank is fool. You can hear the alarm sound.
indicates the ambient relative humidity
appears at the ambient temperature of 5-15 ° C, blinks at> 5 ° C
appears when the ionizer function is activated.
Will appear when the unit is set in the night mode.
Indicates the application time of the filter.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Klimatronic dryfix 3500Klimatronic dryfix 4000

Table des Matières