KitchenAid PRO LINE LAV2701RSS Guide D'utilisation Et D'entretien page 3

Uninstalling Your Washer
WARNING
Excessive Weight Hazard
Use two or more people to move and uninstall washer.
Failure to do so can result in back or other injury.
1. Turn off the hot and cold water faucets.
2. Unplug the power supply cord or disconnect power.
3. Slowly loosen the fill hoses at the faucets to relieve the water
pressure. Use a sponge or towel to absorb the released water.
4. Remove hot and cold fill hoses from the back of the washer.
Drain water in the hoses into a bucket.
5. Squeeze the ears of the drain hose clamp with pliers to open
and slide the clamp down the hose. Disconnect the drain hose
from the washer and drain any water in the hose into a bucket.
6. Pull the washer away from the wall so it can be tipped onto its
back.
7. Protect the floor with a large piece of cardboard cut from the
pedestal carton. Lay the washer on its back (make sure that
the power supply cord is not under the washer) so that the
cardboard is under the entire lower back edge of the washer.
An additional small amount of water will drain out of the
washer when it is tipped back.
8. Go to "Install Pedestal."
Uninstalling Your Electric Dryer
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
1. Unplug the power supply cord.
2. Disconnect wiring if dryer is direct wired.
WARNING
Excessive Weight Hazard
Use two or more people to move and uninstall dryer.
Failure to do so can result in back or other injury.
3. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
4. Pull the dryer away from the wall so that it can be tipped onto
its back.
5. Protect the floor with a large piece of cardboard cut from the
pedestal carton. Lay the dryer on its back (make sure that the
power supply cord is not under the dryer) so that the
cardboard is under the entire back edge of the of the dryer.
6. Go to "Install Pedestal."
Uninstalling Your Gas Dryer
WARNING
Excessive Weight Hazard
Use two or more people to move and uninstall dryer.
Failure to do so can result in back or other injury.
1. Unplug the power supply cord or disconnect power.
2. Turn off the gas supply.
3. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
4. Disconnect the flexible gas supply line from the dryer. Put a
piece of tape over the open ends of the gas line connection
fittings.
5. Pull the dryer away from the wall so that it can be tipped onto
its back.
6. Protect the floor with a large piece of cardboard cut from the
pedestal carton. Lay the dryer on its back (make sure that the
power supply cord is not under the dryer) so that the
cardboard is under the entire back edge of the of the dryer.
7. Go to "Install Pedestal."
Washer or Dryer Is in Its Packaging
WARNING
Excessive Weight Hazard
Use two or more people to move washer or dryer.
Failure to do so can result in back or other injury.
1. Position the packaged washer or dryer close to its final
location, leaving enough room to level the pedestal in the final
location.
2. Follow the Unpacking Instructions to unpack your washer or
dryer.
3. Protect the floor with a large piece of cardboard cut from the
pedestal carton. Lay the washer or dryer on its back (make
sure that the power supply cord is not under the washer or
dryer) so that the cardboard is under the entire back edge of
the of the washer or dryer.
4. Go to "Install Pedestal."
3