Description Of Front Panel - gefran 40T 48 Manuel D'utilisation

Indication of output states:
OUT 1 (Alarm 1); OUT 2 (Alarm 2);
OUT 3 (Alarm 3)
"Raise" and "Lower" keys:
These keys are used for any operation that
requires a numerical parameter to be raised or
lowered. •• The speed of change is proportional
to the time the key is pressed. •• The operation is
not cyclic: once the maximum (minimum) limit is
reached, there will be no further increase
(decrease) of the value, even if the key remains
pressed.
The keys can be configured to perform reset,
hold, display of the peak value, etc. as
determined by the 't.U.' and 't.d.' parameters on
the 'In' menu.
PV display: Indication of process variable ••
Indication of 'HI' or 'Lo' out of range •• Indication
of open circuit (br) or short circuit (Er)
•• Display of configuration and calibration
messages
Indication of output states:
OUT 1 (Alarm 1); OUT 2 (Alarm 2);
OUT 3 (Alarm 3)
• Outputs
Generic user-
-
19
configurable
Out2
outputs
20
+
-
relay 5A/250VAC
-
21
-
logic 6V/20mA,
Out1 Rout = 220Ω
22
+
19 18 7
20 17 8
21 16 9
22 15 10
23 14 11
24 13 12
• Power supply
Standard:
!
100 to 240VAC/DC
±10%
~
23
Optional:
PWR
11 to 27VAC/DC ±10%
~
24
50/60Hz, 7.5VA max.
• Thermocouples
Available thermocouples:
J, K, R, S, T, B, E, N,
2
L, U, G, D, C
- Respect polarities
- For extensions, use
compensated cable
1
appropriate for
thermocouple.
• Pt100 / PTC / NTC
Use wires of
3
adequate thickness
(min. 1mm )
2
2
PT100, JPT100,
PTC, NTC
1
2-wire Pt100
PTC / NTC /
3 • DESCRIPTION OF FRONT PANEL
4 • CONNECTIONS
6
5
22 21 20 19
4
3
1 2 3 4
2
1
• Power supply
Digital input
1500V isolation
6
Ri = 5.6KΩ
(24V, 4mA)
5
• Linear input with 2-wire transmitter
4
-
3
Ri = 50Ω
2
+
1
• Linear input 1V for potentiometer
4
+
3
T T
- 1,2V
2
+
1
3-wire Pt100
• Logic input / Retransmission output / Relay output
Isolated digital input -
6
1500V
Ri = 5.6KΩ
(24V, 4mA)
+
5
18 17 16 15 14 13
5 6 7 8 9 10
• Retransmission output
Analog
retransmission
-
8
output
External
supply 4 to 20mA,
Rmax. 150Ω
+
7
• Inputs
+
+
-
VT
-
4 to 20 mA
dc current
linear input
20mA, Ri = 50Ω
R >100Ω
11
PV display: Indication of process variable ••
Indication of 'HI' or 'Lo' out of range •• Indication
of open circuit (br) or short circuit (Er) •• Display of
configuration and calibration messages
Label with engineering units
Function key:
Gives access to different configuration stages ••
Confirms any parameter changes
Label with engineering units
Generic user-
configurable output
External
- relay 5A/250VAC
supply
Analog output for
retransmission
4 to 20mA, Rmax. 150Ω
• Outputs
Generic user-
configurable outputs
12
- relay 5A/250VAC
for Out1 and Out2
11
- logic 6V/20mA,
Rout = 220Ω
- Triac
20 to 240Vac
±10%
3A max
• Power supply
Standard:
100 to 240VAC/DC
-
±10%
R
Optional: 11 to
27VAC/DC ±10%
+
50/60Hz, 7.5VA max.
• Linear input with 3-wire transmitter
to connect for 20mA input
4
+
3
VT
Ri = 50Ω
-
2
+
1
• Linear (I)
dc voltage
-
4
linear input
60mV, 1V, 5V,
2
10V,
Ri ≥ 500KΩ
+
1
6
Out3
5
-
6
R
+
5
12
Out3
13
TRIAC
-
14 ~
Out2 Line
15
~
+
-
16
Out1
17
+
Load
!
~
11
PWR
~
10
+
S
-
• Linear (V)
2
-
1
+