Recommendations For Optimal Handling Of The Battery; Inserting The Cartridge - Bosch GCG 18V-600 Professional Notice Originale

LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Inserting the sachet (foil bag)
Remove the battery before carrying out any work on
u
the power tool.
When screwing the barrel for sachets (foil bags)/cart-
u
ridges into the caulking gun, ensure that the barrel for
sachets (foil bags)/cartridges is actually being turned
into the thread. Use your other hand to keep a firm hold
of the rear barrel cap when screwing in the barrel for
sachets (foil bags)/cartridges.
The caulking gun is provided for use with sachets (foil bags)
as standard. In this case, no conversion is necessary for ini-
tial use.
When using the caulking gun for the first time, or if a sachet
(foil bag) has been used previously, ensure that the plastic
plunger (4) and metal plunger (5) are installed. Proceed as
follows:
– Unscrew the front barrel cap (1) from the barrel for
sachets (foil bags)/cartridges (2).
– Unlock the rack (7) using the rack release (12) and pull
the rack backwards.
– Cut open the front side of the sachet (foil bag) and push
the sachet (foil bag) into the barrel for sachets (foil bags)/
cartridges.
– Position a suitable dispensing nozzle in front of the sachet
(foil bag) and seal the barrel for sachets (foil bags)/
cartridges (2) with the front barrel cap (1).
– Carefully slide the unlocked rack forwards until the plastic
plunger (4) comes into contact with the sachet (foil bag).
– If necessary, cut the dispensing nozzle to size, so that it
ideally meets your requirements.
If the caulking gun has been used previously with a cartridge,
proceed as follows (see figure A):
– Unlock the rack (7) using the rack release (12) and pull
the rack backwards.
Bosch Power Tools
– Unscrew the barrel for sachets (foil bags)/cartridges (2)
Capacity
from the caulking gun.
40–60 %
– Remove the aluminium press (6), turn it 180° (domed
20–40 %
side is now facing the back) and replace it.
5–20 %
– First place the metal plunger (5), then the plastic
0–5 % plunger (4), onto the aluminium press (6). Screw the
clamping nut (3) onto the thread and tighten.
– Screw the barrel for sachets (foil bags)/cartridges (2)
onto the caulking gun. When doing so, hold the rear barrel
cap (8) in place.
– Unscrew the front barrel cap (1) from the barrel for
sachets (foil bags)/cartridges (2).
– Cut open the front side of the sachet (foil bag) and push
the sachet (foil bag) into the barrel for sachets (foil bags)/
cartridges (2).
– Position a suitable dispensing nozzle in front of the sachet
(foil bag) and seal the barrel for sachets (foil bags)/
cartridges (2) with the front barrel cap (1).
– Carefully slide the unlocked rack forwards until the plastic
plunger (4) comes into contact with the sachet (foil bag).
– If necessary, cut the dispensing nozzle to size, so that it
ideally meets your requirements.

Inserting the Cartridge

If the caulking gun has been used previously with a cartridge,
proceed as follows:
– Unlock the rack (7) using the rack release (12) and pull
the rack backwards.
– Unscrew the front barrel cap (1) from the barrel for
sachets (foil bags)/cartridges (2).
– Cut open the front side of the cartridge and screw on a
dispensing nozzle.
– Insert the cartridge and seal the barrel for sachets (foil
bags)/cartridges (2) with the front barrel cap (1).
– Carefully slide the unlocked rack forwards until the alu-
minium press (6) comes into contact with the cartridge.
– If necessary, cut the dispensing nozzle to size, so that it
ideally meets your requirements.
If the caulking gun has been used previously with a sachet
(foil bag), proceed as follows (see figure B):
– Unlock the rack (7) using the rack release (12) and pull
the rack backwards.
– Unscrew the barrel for sachets (foil bags)/cartridges (2)
from the caulking gun.
– Remove the plastic plunger (4) and the metal plunger (5)
by twisting off the plastic plunger.
– Remove the aluminium press (6), turn it 180° (domed
side is now facing inwards) and replace it. Secure the alu-
minium press (6) using the clamping nut (3).
– Screw the barrel for sachets (foil bags)/cartridges (2)
onto the caulking gun. When doing so, hold the rear barrel
cap (8) in place.
– Unscrew the front barrel cap (1) from the barrel for
sachets (foil bags)/cartridges (2).
English | 15
1 609 92A 7G3 | (29.03.2022)