Safety Warnings; Functional Description; Intended Use - stayer DM1600 Instructions D'emploi

This manual is consistent with the date of manufacture
of your machine, you will find information on the
technical data of the
check for updates of our machines on the website:
www.grupostayer.com

Safety Warnings

- Do not use the power tool for explosive materials (e.
g, easily inflammable solvents). Power tools produce
sparks which could ignite developing vapours.
- In case the power tool should fall into the material
to be stirred, pull the plug immediately and have the
power tool checked by an after-sales service agent.
Material that has penetrated the power tool can cause
damage and lead to an electric shock.
- Always use the auxiliary handle supplied with the
machine. Loss of control can cause personal injury.
- When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
- Do not work materials containing asbestos. Asbestos
is considered carcinogenic.
- Take protective measures when dust can develop
during working that is harmful to one's health,
combustible or explosive. Example: Some dusts are
regarded as carcinogenic. Wear a dust mask and work
with dust/chip extraction when connectable.
- Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam
and lead to loss of control over the power tool.
- Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug
when the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
- Connect machines that are used in the open via a
residual current device (RC D).
Batteries use and care
Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and seek
medical help in case of complaints. The vapours can
irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The battery
machine acquired manual
ENGLISH
14
can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot
be subject to overload. When the load is too high or
the allowable battery temperature range of 0–50 °C
is exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation direction
. This automatically locks the drill chuck.
The locking is released again to remove the tool when the
collar is turned in the opposite direction.

Functional Description

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.

Intended Use

The power tool is designed to remove powdered building
materials such as mortars, plasters, adhesives and paints,
lacquers or similar substances which are also solvent-free.
The values given are valid for nominal voltages [U] of 230/240
V ~ 50/60 Hz - 110/120 V ~ 60 Hz. For lower voltage and
models for specific countries, these values can vary.
Please observe the article number on the type pl ate of your
machine. The trade names of the individual machines may
vary.Product Features
The numbering of the product features refers to the illustration
of the machine on the graphics page.
1. Mechanical velocity selector.
2. Auxiliary handle.
3. Propeller stirrer
14