Dip Switch Settings - Haier GE Appliances USYM09UCDS Manuel D'utilisation

Installation Instructions
G.
Continued.
H.
External Static Pressure Setting
Using Wired Controller
Wired controller- QACT17A settings
1. After backlight is lit at the wired controller off, press
and hold FAN and TEMP + button for 10 seconds.
2. The static pressure selection will appear in the
upper right hand corner.
3. The parameter value of ESP grades can be
adjusted by pressing TEMP+ or TEMP- buttons.
4. Press FAN button to confirm the change.
ESP Level (ESP grade)
1
2
3
4
5
6
7
8
9
10
Use the Up and Down Arrow buttons to adjust the
static pressure level numbers. Then press the Set
button to confirm.
10
Step 2 - Mounting the Unit (Cont.)
0.10 in WC.
0.15 in WC.
0.20 in WC.
0.28 in WC.
0.36 in WC.
0.40 in WC.
0.44 in WC.
0.48 in WC.
0.52 in WC.
0.60 in WC.
I.

DIP Switch Settings

After attaching the 14/4 stranded copper wire to the terminal
block, the DIP switch bank on the PCB need to be checked.
Need to make sure all switches are in the correct position
including a field-supplied external static pressure setting per
the table below.
SW3_1 Special fresh [1]
Air (Canada
particular Area)
SW3_2 Reserved [2]
SW3_3 Auxiliary [3]
heater
SW3_4 Slim duct or [4]
MESP DUCT
[5]
OFF OFF
OFF OFF
OFF OFF
OFF OFF
SW3_5 IDU address
OFF ON
SW3_6 for wired
OFF ON
SW3_7 controller
OFF ON
SW3_8 group
OFF ON
Control
ON
application
ON
ON
ON
ON
ON
ON
ON
[1]
OFF OFF
ON
SW1_1
OFF ON
SW1_2 Capacity
ON
SW1_3 OFF OFF
ON
OFF ON
ON
SW1_4 Room card OFF
ON
SW1_5 Heat pump / OFF
Cool only
ON
SW1_6 Fresh air/E.A.O OFF
ON
SW1_7 Filter change OFF
caution
ON
SW1_8 North America/ OFF
NON- North
America
ON
ON Special Fresh Factory default
Air function setting: OFF
valid
OFF Special fresh
Air funtion
invalid
ON Reserved Factory default
OFF Reserved setting: OFF
ON Auxiliary Factory default
heater setting: OFF
Function valid
OFF Auxiliary
heater
Function
invalid
ON MESP DUCT Factory default
(10 ESP level) setting: According
to model
OFF Slim DUCT (10
ESP level)
[6] [7] [8] IDU Address
OFF OFF 0# (main)
(Factory default
setting)
OFF ON 1# (subordinate)
ON OFF 2# (subordinate)
ON ON 3# (subordinate)
OFF OFF 4# (subordinate)
OFF ON 5# (subordinate)
ON OFF 6# (subordinate)
ON ON 7# (subordinate)
OFF OFF OFF 8# (subordinate)
OFF OFF ON 9# (subordinate)
OFF ON OFF 10# (subordinate)
OFF ON ON 11# (subordinate)
ON OFF OFF 12# (subordinate)
ON OFF ON 13# (subordinate)
ON ON OFF 14# (subordinate)
ON ON ON 15# (subordinate)
[2] [3] Capacity
OFF 9000BTU/h
OFF OFF 12000BTU/h
OFF 18000BTU/h
ON OFF 24000BTU/h
ON Reserved
OFF ON Reserved
ON Reserved
ON ON Reserved
Room card invalid (factory
default)
Room card valid
Heat pump (factory
default)
Cool only
Fresh air valid (factory
default)
External alarm output valid
Without filter change
caution (factory default)
With filter change caution
North America area (USA
& Canada) (factory default)
NON-North America
31-5000493 Rev. 1