Table des Matières
Publicité
The accessories contained in the model you have just purchased are represented on the label located on top
of the packaging.
CAUTION: the safety precautions are part of the ap-
EN
pliance. Read them carefully before using your new ap-
pliance for the first time. Keep them in a place where you
can find and refer to them later on.
Description
a
Motor drive
a1 : Motor drive slow output
a2 : Motor drive fast output
a3 : Speed selector: Pulse position (intermittent
operation)-0-1-2
ACCESSORIES DEPENDING ON MODEL:
d
Multifunction blade
e
Emulsifying disc
f
Vegetable cutter cartridges
A : Fine grater
D : Fine slicer
C : Coarse grater
G : Rosti (potato cakes)/parmesan
H : Thick slicer
E : French fries cutter
g
Cartridge holder
h
Blender
h1 : Feeder cap
h2 : Lid
h3 : Jug
Using your appliance
• Before using for the first time, wash all parts of the accessories in hot soapy water (see section on cleaning).
Rinse and dry.
(a)
• Place the motor drive
on a flat surface that is clean and dry.
• Plug in your appliance.
• Pulse (intermittent operation): turn the knob
better control when preparing certain foods.
(a3)
• Continuous operation: turn the knob
(a3)
• Stop: turn the knob
to position 0.
The numbering of the paragraphs corresponds to the numbering of the diagrams.
1 : Fitting the chopping bowl and lid
ACCESSORIES USED:
(b)
• Bowl assembly
.
FITTING THE ACCESSORIES:
(b3)
• Place the bowl
on the motor drive
(b3)
• Lock the bowl
by turning it to the right.
b
Chopping bowl assembly
b1 : Pusher with measuring section
b2 : Lid with feeder tube
b3 : Bowl
c
Spindle
i
Citrus press
i1 : Cone
i2 : Citrus press spindle
i3 : Filter basket
j
Herb grinder
j1 : Lid
j2 : Herb grinder bowl
k
Spatula
l
Storage drawer
(a3)
to Pulse position - using a succession of pulses can give you
to position 1 or 2.
(a)
, with the handle positioned slightly to the right of the button.
10
(b2)
(b3)
• Fit the lid
onto the bowl
. Lock the lid by pushing it to the right in the bowl handle.
It is essential to lock the bowl onto the motor drive
2 : Removing the chopping bowl and lid
• Unlock the lid by turning it clockwise to release the bowl handle. You will then be able to lift and remove it.
• Unlock the bowl by turning it clockwise.
• Only now will you be able lift and remove the bowl from the motor drive.
3 : Mixing/blending/chopping/kneading
ACCESSORIES USED:
(b)
• Bowl assembly
.
(c)
• Spindle
.
(d)
• Multifunction blade
.
FITTING THE ACCESSORIES:
(b3)
(a)
• Place the bowl
onto the motor drive
and lock it in place.
(d)
• Slide the multifunction blade
onto the spindle
• Place the ingredients in the bowl.
(b2)
(b3)
• Place the lid
and lock it on the bowl
.
• To remove the bowl-lid assembly: unlock the lid then unlock the bowl.
KNEADING/MIXING
(a3)
• Turn the speed selector
to position 2 to start it up.
You can knead up to:
- 1 kg of heavy dough, such as white bread dough, shortcrust pastry in 60 sec.
- 800g of special bread dough, such as rye bread, wholemeal bread, wholegrain bread, etc. in 60 sec.
You can mix up to:
- 1.2 kg of light cake mixture such as biscuit dough, pound cake, sponge cake, etc. in approximately 1 min
30 sec to 3 min.
You can also mix up to 1 litre of pancake or waffle batter in 1 min to 1 min 30 sec.
CHOPPING
(a3)
• Turn the speed selector
to position 2 to start, or for better control of chopping, use the pulse position.
You can chop up to 600 g of food such as:
- Raw or cooked meat (boned, trimmed and diced).
- Raw or cooked fish (skinned and filleted).
- Hard foods: cheese, dried fruit, some vegetables (carrots, celery, etc.).
- Soft foods: some vegetables (onions, spinach, etc.).
BLENDER
(a3)
• Turn the speed selector
to position 2 to start.
You can blend up to 1 litre of soup or stewed fruit in 45 sec.
ACCESSORIES USED:
(b)
• Bowl assembly
.
(c)
• Spindle
.
(f)
• Cartridge of choice
(depending on model).
(g)
• Cartridge support
.
FITTING THE ACCESSORIES:
(b3)
(a)
• Place the bowl
on the motor drive
and lock it.
(f)
• Insert the selected cartridge
into the cartridge support
(c)
axle
as far as it will go through the cartridge
(a1)
position it on the motor drive
.
(b2)
(b3)
• Fit the lid
and lock it on the bowl
• To remove the bowl-lid assembly: unlock the lid and then unlock the bowl.
(a)
(b2)
before locking the lid
onto the bowl
(c)
, and position the entire assembly on the motor drive
4 : Grating/slicing
Check that the
metal axle of
the spindle (c) is
(g)
, introduce the spindle
inserted in the
(f)
, and lock the assembly, then
centre of the lid
with measuring
tube (b2)
11
(b3)
.
EN
(a1)
.
Publicité
Table des Matières
