Télécharger Imprimer la page

Publicité

Liens rapides

Read and understand "Safety Instructions For Air Tools" and these instructions before oper-
Tools left connected to the air supply while making adjustments, changing accessories, or doing any mainte-
Always remove tool from air supply and activate trigger to bleed air line before making any adjust-
ments, changing accessories, or doing any maintenance or service on tool.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter, pressure regulator, and
lubricator will insure maximum output and service life of tools.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 5/16" (7.9mm) I.D. Extension hoses should be at least 3/8" (10mm) I.D. Use couplings and fittings with at
least 5/16" (7.9mm) I.D.
LUBRICATION
An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04oz. (1.2cc) of SIOUX No. 288 air
motor oil into the air inlet daily.
Lubricate the gearing with SIOUX No. 1232A grease after every 50 hours of operation.
GENERAL OPERATION
This tool is equipped with a teasing throttle. By slightly depressing the trigger the chuck will rotate slowly. This is useful for starting a drill bit without
first spotting with a punch. Fully depressing the trigger for maximum speed.
A speed control adjusting screw is located on the trigger face and is adjusted with a 1/16" (1.6mm) hex key wrench.
We, Sioux Tools Inc., 2901 Floyd Boulevard, P.O. Box 507, Sioux City Iowa, 51102, USA, declare under our sole responsibility that the
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
INSTRUCTIONS 1407 AIR DRILL
ating this tool.
nance or service on tool can start unexpectedly.
Tools starting unexpectedly can cause injury.
SOUND AND VIBRATION READINGS
Sound Pressure
Catalog No.
dBA
1407
72.48
*prt PN8NTC1
DECLARATION OF CONFORMITY
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
January 1, 1997
Sioux City, Iowa,
Sioux Tools Inc.
USA
Name and position of
Date and place of
issues
Sound Power
Vibration
dBA
m/s
83.45
Less than 2.5
*prt PN8NTC1
*per ISO8662
products
1407
R. V. Caskey
President
Signature of issuer
issuer
1
Form ZCE428B
Date 5-97
2
Printed In U.S.A.

Publicité

loading

Sommaire des Matières pour SIOUX 1407

  • Page 1 5/16" (7.9mm) I.D. LUBRICATION An airline lubricator, set to deliver one drop per minute, is recommended. If a lubricator is not used, add .04oz. (1.2cc) of SIOUX No. 288 air motor oil into the air inlet daily. Lubricate the gearing with SIOUX No. 1232A grease after every 50 hours of operation.
  • Page 2 *prtPN8NTC1 *prtPN8NTC1 *gemäß ISO8662 DECLARACION DE CONFORMIDAD Nosotros, Sioux Tools, Inc., 2901 Floyd Boulevard, P.O. Box 507, Sioux City, Iowa, 51102, USA, declaramos bajo nuestra única responsa- ÜBEREINSTIMMUNGSERKLÄRUNG bilidad que los productos Wir, Sioux Tools, Inc., 2901 Floyd Boulevard, P.O. Box 507, Sioux City, Iowa, 51102, USA, erklären hiermit alleinverantwortlich, daß die...
  • Page 3 1407 La Sioux Tools, Inc, con sede al 2901 Floyd Boulevard, P.O. Box 507, di Sioux City, Iowa, USA, solennemente dichiara sotto la propria e dont cette fiche fait l’objet, sont conformes aux normes, documents normatifs et autres références : sola responsabilità...
  • Page 4 CONFORMITEITSVERKLARING Vi, Sioux Tools, Inc., 2901 Floyd Boulevard, P.O. Box 507, Sioux City, Iowa, 51102, USA, förklarar under eget ansvar att produkterna Ondergetekende, Sioux Tools, Inc., 2901 Floyd Boulevard, P.O. Box 507, Sioux City, Iowa, 51102, USA, verklaart met inachtneming van...
  • Page 5 PARTS LIST FOR 1407 AIR DRILL SERIAL “B” Fig. Part Fig. Part Description Description 21019 Chuck—1/4” Capacity 30375 Fitting—Grease 30202 Key—Chuck 66299 Pin—Groove 44122 Spacer—Chuck 21441 Spring 67773 Retainer 66300 Assembly—Trigger 41226 Washer—Spring Wave 14349 Ring—“O” 43804 Assembly—Planetary Reduction 66247 Rod—Trigger (Includes Figures 6 thru 11) 21542 Ring—Retaining...
  • Page 6 MEMO MEMO...
  • Page 7 Printed In U.S.A.
  • Page 8 This pdf incorporates the following model numbers: 1407...