Delivery Content; Operating Elements; Safety Instructions - Renkforce GH-4200E Mode D'emploi

Operating Instructions
4+2 Port Gigabit PoE + SFP Switch for DIN Rail
Item No. 1697438
Intended Use
This product is an industrial 4+2 Port Gigabit PoE with SFP switch that is designed for small to
medium sized network environments. It has a broad operating temperature range and comes
with a DIN rail mount. The terminal block supports two power sources for situations where an
alternative power supply is required. A DIP switch can be set to trigger an alarm when a network
connection is severed or if a power source fails.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture must be avoided
under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, fires, electric shocks or other hazards. Read
the instructions carefully and store them in a safe place. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.

Delivery Content

• Unit
• 6-pin terminal block
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.

Safety Instructions

Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the device from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Consult an expert when in doubt about the operation, safety or connection of the
appliance.
• Installation, maintenance, modifications and repairs must only be completed by a
technician or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Location
• In schools, training facilities, hobby or self-service workshops, handling of
electrical devices must be monitored by trained personnel.
• When operating on commercial premises, the relevant accident prevention
regulations of workers' compensation boards for electrical equipment must be
observed.
c) Installation
• The electrical installation of the product must be handled by a professional,
familiar with the applicable laws and standards.
d) Product
• Install the switch in an environment compatible with the operating temperature
range specified in "Technical Data".
• Switches installed in a closed or multi-unit rack assembly can experience a greater
operating ambient temperature than the ambient room temperature.
• Install the switch in a way that allows sufficient airflow for proper operation.
• When installing the switch avoid overloading the circuits and make sure the switch
is properly grounded.
• Only use only the provided hardware to install the DIN-Rail.
• Do not use the device as a shelf.
• Never install communications wiring or components during a lightning storm.
• Be aware of loose or damaged cable connections. Never touch bare wires or
terminals unless the wiring has been disconnected at the network interface.
• Use caution when installing or modifying wiring or components. Disconnect the
power supply before connecting / disconnecting equipment.

Operating Elements

1
2
3
4
5
1 PWR1 / PWR2 LED (power)
2 DIN-rail mount
3 Grounding connection
4 44 - 57 V/DC 6-pin terminal input
5 DIP switches
Installation
There is a risk of a life-threatening electric shock!
The electrical installation (such as wiring) of the product must be handled by a
professional, who is familiar with the regulations and safety precautions.
Be especially careful when installing the product in an electrical control cabinet with
dangerous voltages.
Only connect and install the product, when it is disconnected from the mains voltage.
Use caution when installing or modifying wiring or components. Always disconnect
the power supply before connecting / disconnecting equipment.
See 'Technical data' for suitable installation environments (IP class).
Depending on your installation location you either place the product onto the DIN
rail first and then connect power, or the other way round. Read the corresponding
section in this chapter first.
At all times, make sure not to supply any power to the product as long as installation
is not completed.
6
7
8
9
10
11
6 Alm LED (alarm
7 SFP1 / SFP2 LED
8 SFP Port
9 PoE LED
10 Link/Act LED
11 PoE port