Important Charging Notes - Porter Cable PCC621 Manuel D'instructions

PCC692/PCC692L in 40-80 mins., and
PCC695L in 180-360 mins. depending on
the pack being charged.
1. Plug the charger into an appropriate
outlet before inserting the battery pack.
2. Insert the battery pack into the charger.
3. The LED will flash indicating that
the battery is being charged.
4. The completion of charge is indicated
by the LED remaining on continuously.
The pack is fully charged and may be used at
this time or left on the charger.
Recharge discharged batteries as soon
as possible after use or battery life
may be greatly diminished. For longest
battery life, do not discharge batteries
fully. It is recommended that the batteries
be recharged after each use.
Charger Diagnostics
This charger is designed to detect
certain problems that can arise with the
battery packs or the power source. Problems
are indicated by one LED flashing in different
patterns.
Bad Battery
The charger can detect a weak or
damaged battery. The LED flashes in
the pattern indicated on the label. If you see
this bad battery blink pattern, do not continue
to charge the battery. Return it to a service
center or a collection site for recycling.
Hot/Cold Pack Delay
When the charger detects a battery
that is excessively hot or excessively
cold, it automatically starts a Hot/Cold
Pack Delay, suspending charging until the
battery has normalized. After this happens,
the charger automatically switches to the
Pack Charging mode. This feature ensures
maximum battery life. The light flashes in
the pattern indicated on the label.
Problem Power Line
When the charger is used with some
portable power sources such as
generators or sources that convert DC to
AC, the charger may temporarily suspend
operation. The LED flashes in the pattern
indicated on the label. This indicates that
the power source is out of limits.
Leaving the Battery in the Charger
The charger and battery pack can be
left connected with the LED glowing
indefinitely. The charger will keep the
battery pack fresh and fully charged.
This charger features an automatic tune-
up mode which equals or balances the
individual cells in the battery pack to allow
it to function at peak capacity. Battery
packs should be tuned up weekly or
whenever the battery no longer delivers the
same amount of work. To use the automatic
tune-up mode, place the battery pack in the
charger and leave it for at least 8 hours.

Important Charging Notes

1. Longest life and best performance can
be obtained if the battery pack is charged
when the air temperature is between 65°F
and 75°F (18°- 24°C). DO NOT charge
the battery pack in an air temperature
below +40°F (+4.5°C), or above +105°F
(+40.5°C). This is important and will
prevent serious damage to the battery
pack.
2. The charger and battery pack may
become warm to touch while charging.
This is a normal condition, and does
not indicate a problem. To facilitate the
cooling of the battery pack after use,
avoid placing the charger or battery pack
in a warm environment such as in a metal
shed, or an uninsulated trailer.
3. If the battery pack does not charge
properly:
a. Check current at receptacle by
plugging in a lamp or other appliance
b. Check to see if receptacle is
connected to a light switch which turns
power off when you turn out the lights.
c. Move charger and battery pack to a
location where the surrounding air
temperature is approximately 65°F -
75°F (18°- 24°C).
d. If charging problems persist, take
the tool, battery pack and charger to
your local service center.
4. The battery pack should be recharged
when it fails to produce sufficient
power on jobs which were easily done
previously. DO NOT CONTINUE to
use under these conditions. Follow the
charging procedure. You may also charge
a partially used pack whenever you desire
with no adverse affect on the battery
pack.
Safety Warnings and
Instructions: Drills
WARNING
instructions and cautionary markings on
tool.
WARNING
or improperly used) causing a twist. Always
expect the stall. Grip the drill firmly with two
hands to control the twisting action and
prevent loss of control which could cause
personal injury. If a stall does occur, release
the trigger immediately and determine the
reason for the stall before re-starting.
7
:
Before using tool, read all
:
Drill may stall (if overloaded