Bostitch BCN662 Manuel D'instructions page 12

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

English

WARNING: Always remove battery pack before
loading or unloading nails. Serious personal injury
may result.
1. Load nails through the slot in the rear of the magazine
and past the retaining clip.
2. Pull pusher 
back behind nail stick and release.
 16 
3. Ensure magazine pusher
Fig. H
7
Unloading The Tool (Fig. H)

WARNING: The trigger lock-off should always be
locked off whenever any adjustments are made or
when tool is not in use.
1. Release pusher so it is no longer applying force to the
nail sticks.
2. Slide nail sticks down and out through the slot in the
rear of the magazine.
3. Open the jam clear door  
there are no nails remaining.
Mode Selection (Fig. I)

WARNING: Always wear proper eye [ANSI Z87.1
(CAN/CSA Z94.3)] and ANSI S12.6 (S3.19) hearing
protection when operating tool.
The BOSTITCH cordless nailers are assembled in accordance
with the ANSI Standard SNT-101-2002.
The finish nailer is capable of firing nails using bump
actuation or sequential actuation. If you would like to
have the bump actuation mode disabled, have the tool
serviced by an authorized BOSTITCH service center. Before
operating this tool, look at the selector switch to determine
the actuation mode. Read all instructions before selecting
actuation mode.

WARNING: Keep fingers AWAY from trigger when not
driving nails to avoid accidental fastener discharge.
NEVER carry tool with finger on trigger. In bump
mode tool will drive a nail if contact trip is bumped
while trigger is depressed.
Sequential Actuation
Use sequential actuation mode for intermittent nailing
where very careful and accurate placement and depth
control is desired. The sequential actuation mode provides
the maximum delivery of power for driving the longest nails.
10
is behind the last nail stick.
7
16
 5 
on the nosepiece to verify
To operate the nailer in sequential actuation mode:
1. Slide the selector switch 
icon 
.
2. Fully depress nosepiece against the work surface (motor
will start).
3. Pull trigger (nail will drive into work surface).
4. Release trigger.
5. Lift nosepiece off work surface.
6. Repeat steps 2 through 4 for next application.
NOTICE: The contact trip needs to be depressed followed
by a trigger pull for each nail followed by a release of both
the contact trip and trigger after each nail.
Fig. I
Bump action
Bump action is intended for rapid nailing on flat, stationary
surfaces and typically most effective for applications that
require driving shorter nails.
When the tool is set in the bump actuation mode, two
methods of tool operation are available: place actuation
and bump actuation.
Slide the selector switch 
 8 
to expose the triple nail 
icon
.
To operate the tool using the place actuation
method:

WARNING: A nail will be driven each time the
trigger is depressed as long as the contact trip
remains depressed.
1. Depress the contact trip against the work surface.
2. Depress the trigger.
To operate the tool using the bump actuation
method:
1. Depress the trigger.
2. Push the contact trip against the work surface. As long
as the trigger is depressed, the tool will drive a nail every
time the contact trip is depressed. This allows the user
to drive multiple nails in sequence.

WARNING: Do not keep trigger depressed when tool
is not in use. Keep the trigger lock-off in the locked
position when the tool is not in use.

WARNING: When the tool's motor is running, pulling
the trigger or depressing the contact trip will cause a
nail to be driven.
Adjusting Depth (Fig. J)
The depth that the fastener is driven can be adjusted using
the depth adjustment wheel 
 8 
to expose the single nail
8
 3 
on the side of the tool.

Publicité

Table des Matières
loading

Table des Matières