Publicité

®
25267801
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©
2015 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
This equipment has been tested and found to comply with the limits for a class B digital device pursuant
to Part 15 for FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the
separation between the equipment and receiver. • Connect the equipment into an outlet or a circuit different
from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician
for help.
This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
o
Ology
90
& 120
o
Corner Desks
3, 4, 5 & 6MM
#2
10MM
3, 4, 5 & 6MM
TORQUE
WRENCH
Page 1 of 21
P/N 25267801
Doc # 67489 Rev R

Publicité

Table des Matières
loading

Sommaire des Matières pour Steelcase Ology

  • Page 1 Part 15 for FCC rules. These limits are designed to provide reasonable protection against harmful WRENCH your local dealer, or Steelcase Line 1 at interference in a residential installation. This equipment generates, uses and can radiate radio frequency 888.STEELCASE (888.783.3522) energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 2: Important Safety Instructions

    4. Never operate this table if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. If the cord is damaged, have it replaced by a Steelcase dealer.
  • Page 3: Conservez Ces Directives

    Nunca use esta mesa si tiene un cable o enchufe dañado, si no está funcionando correctamente, si se ha caído o dañado, o si se le ha dejado caer en el agua. Si el cable está dañado,...
  • Page 4 ® NOTE: Both the corner and the extension pieces have been marked with a number to ensure the correct installation of the unit. Please make sure to install corner piece 1 with extrusion piece 1 and so forth. Page 4 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 5 ® 29” 23” NOTE: This part is handed. (RH shown in isometric view) NOTE: Loosen glides. NOTE: Attach one leg only. Longer cables - 2 M .905" (23mm) 4x (23") NOTE: Install frame 6x (29") tube with frame tube NOTE: Thicker edgeband Page 5 of 21 Shorter cable - 1 M holes oriented toward...
  • Page 6 ® Loosen bolts almost all the way. NOTE: Installer will tighten these bolts on Step 17. Tube Orientation: Hole in tube can face front or back. Place towards back if there is no Power Access Door, Cable Tray, or Basket. Page 6 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 7 ® NOTE: Loosen glide. Page 7 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 8 ® NOTE: Install frame tube with frame tube holes oriented toward the rear corner. Page 8 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 9 ® NOTE: Loosen glides. 6mm Hex 17 4X 25 Nm (221 in-lbs) Page 9 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 10 ® Placement of Control Box ______________________ If you have a Cable Basket or Power Access Door in the Back, place Control Box in the Front of the Frame Tube. Otherwise, place the Control Box behind the Frame Tube for best knee clearance. Place Control Box on the same side as the desired User Switch location (Left or Right).
  • Page 11 ® To Strain Relief Power Cord Page 11 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 12 For 4 Preset Only ® 4 Preset Active & Simple Touch NOTE: Gasket for Simple Touch Only. Page 12 of 21 See Arrow for correct orientation. P/N 25267801 Doc # 67489 Rev R...
  • Page 13 ® Press down to initialize the desk, holding for 3 seconds. After initialization, the legs will 22.6" now adjust vertically. 27.3" Plug the desk into power For Active Touch Only: Tap the Switch. Each time it is pressed, it will toggle between 22.6"...
  • Page 14 ® Rail Option: (If Applicable) Page 14 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 15 ® Page 15 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 16 ® Page 16 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 17 ® Rail Access Door Option: (If Applicable) Page 17 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 18 ® Page 18 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 19 ® Grommet Option: (If Applicable) For Elective Elements Worksurface Only: Page 19 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 20 ® Page 20 of 21 P/N 25267801 Doc # 67489 Rev R...
  • Page 21 ® Page 21 of 21 P/N 25267801 Doc # 67489 Rev R...

Table des Matières