Niko Easywave Guide Rapide page 6

05-361
Indication Status
- The status LED flashes red or The battery is almost empty.
green for three seconds.
- A notification has been
transmitted.
- The status LED flashes red two
times in succession every nine
seconds.
- The contact is deactivated.
The status LED turns red after The battery is empty.
you have installed a battery.
The status LED turns red and Je hebt een eerdere melding
stays red without flashing. genegeerd om de batterij te
vervangen. Het contact kan niet
meer werken.
De spanning van de batterij is
te laag.
How do I replace the battery?
1. Screw open the top of the contact.
2. Pull on the lip to remove the battery holder from the contact, and replace the battery. Pay attention to
the polarity: the positive pole must be visible.
Tip: Only use type CR2032 batteries.
3. Screw the top of the housing back onto the contact.
Attention: The coding of the contact is maintained even if the contact is live. After you have replaced
the battery, you do not have to reprogram the coding on the selected wireless Easywave receiver.
4. TROUBLESHOOTING
1. If the Easywave system does not work after being programmed, you can always first perform a
number of extra checks:
• Check whether the shield between the battery and the contacts in the contact has been
removed.
• Check whether there is good contact integrity between the battery and the battery
contacts.
• Check the operation of the connected receiver. Press the programming button (P) on the front
of the receiver. If the status LED does not flash, the receiver is defective.
• Check the operation of the contact. Take the contact and walk toward the receiver:
- - The Easywave system only works if you bring it closer to the receiver. Use a wireless
Easywave repeater (05-535) to increase the range.
- - If the Easywave system does not work at all, even when you bring the contact closer to the
receiver, check the programming and/or the batteries of the contact.
• In the case of an existing installation, check whether the surroundings of the Easywave
system have changed, possibly causing interference (metal electricity cabinet, walls, moved
furniture ...). Restore the original arrangement, if possible.
2. If the problem with the device is not solved, then go through the following list of possible problems:
Problem Cause
The receiver does not react to The battery is empty or almost
the contact. empty.
In certain situations, other
wireless products that work on
the same frequency and are
located in the immediate vicinity
of the contact and the receiver
can cause interference.
The programming was not
successful or was erased.
5. TECHNICAL DATA
dimensions
weight
frequency
modulation
power supply
power consumption
range
protection degree
6
operating temperature
quality mark
EN nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
Action
You must replace the battery
soon.
You must replace the battery
immediately.
Solution
- Check the status of the battery.
- If necessary, replace the
battery.
Check whether the signal
transmission between transmitter
and receiver is not obstructed.
Program the codes again on
the selected wireless Easywave
receiver. To do this, consult the
user manual of the receiver.
contact: 12 x 65 x 28 (HxWxD)
magnet: 18 x 18 x 13 (HxWxD)
contact: 20.6 g
magnet: 2.2 g
868.3 MHz
FSK
3 V battery, type CR2032
1.6 µA
approximately 150 m in open spaces
IP54
-20 – +60°C
CE marking in accordance with EN 60669-2-1
6. WARNINGS REGARDING INSTALLATION
- The installation should be carried out by a registered installer and in compliance with the statutory regulations.
- This manual should be presented to the user. It should be included in the electrical installation file, and it
should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
- During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope of
each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
7. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
8. GUARANTEE PROVISIONS
- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating
the defect.
- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge,
which shall be decided by Niko.
- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
- The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
PM005-36300R13485