Dimensional Drawings; Ordering Information - SICK SFS60S Notice D'instruction

Output frequency for sine/cosine signals
Weight
Operating torque at 20 °C
Rotor moment of inertia
Max. permitted angular acceleration
Max. operating speed
1
Start up torque at 20 °C
Service life of ball bearings
2
Radial shaft movement, static
Radial shaft movement, dynamic
Shaft movement, axial, static
Shaft movement, axial, dynamic
Ambient data
Operating temperature
M23 male connector, 12-pin, radial
M12 male connector, 8-pin, radial
Cable, 8-wire, radial, 1.5 m
Storage temperature range (without packaging)
M23 male connector, 12-pin, radial
M12 male connector, 8-pin, radial
Cable, 8-wire, radial, 1.5 m
Relative humidity/condensation
Resistance to shocks
Resistance to vibrations
(in accordance with EN 60068-2-6)
M23 male connector, 12-pin, radial
M12 male connector, 8-pin, radial
Cable, 8-wire, radial, 1.5 m
EMC
Enclosure rating
Safety-related parameters
Safety integrity level
5
Performance Level
4
Category
Probability of a dangerous failure per hour (PFH
Mission time (T ) 2
M
Test rate
Max. request time
Safety-related accuracy
6
Safety-related measuring increment
Self-heating approx. 3.0 K per 1,000 rpm, note working temperature range in design.
1
The mission time can also be limited by the bearing service life specific to the applica‐
2
tion.
The EMC according to the standards quoted is achieved when the motor feedback sys‐
3
tem is mounted in an electrically conductive housing, which is connected to the central
earthing point of the motor controller via a cable screen. The GND-(0 V) connection of
the supply voltage is also grounded here. If other shielding concepts are used, users
must perform their own tests.
The enclosure rating (in accordance with IEC 60529) is achieved with attached mating
4
connector and was tested with the shaft in a horizontal position.
For more detailed information on the exact configuration of your machine/unit, please
5
consult your relevant SICK branch office.
The values displayed apply to a diagnostic degree of coverage of 90%, which must be
6
achieved by the external drive system.In the event of resonance, suitable tests have to
be carried out on the entire drive system.
8021186/14HP/2019-07-04/de, en, es, fr, it
SFS60S SFM60S
0 kHz ... 200 kHz
≤ 0.25 kg
0.6 Ncm
56 gcm²
≤ 500,000 rad/s²
6,000 rpm
0.8 Ncm
3.6 × 10 Rotations
9
± 0.3 mm
± 0.05 mm
± 0.5 mm
± 0.1 mm
–30 °C ... +95 °C
–30 °C ... +95 °C
–30 °C ... +85 °C
–40 °C ... +100 °C
–40 °C ... +100 °C
–40 °C ... +90 °C
90%, condensation not permitted.
100 g / 6 ms (in accordance with EN
60068-2-27)
10 g / 10 ... 1,000 Hz
20 g / 10 ... 2,000 Hz
20 g / 10 ... 2,000 Hz
EN 61000-6-2, EN 61000-6-3
IP 65
4
SIL2 (IEC 61508), SILCL2 (EN 62061)
PL d (EN ISO 13849)
3 (EN ISO 13849)
)
4 1.7 x 10
-8
D
20 years (EN ISO 13849)
Not required
Continuous (analog signals)
± 0.09° (for square counting)
0.09° (for square counting)

9.1 Dimensional drawings

2
1
Figure 1: Dimensional drawing of through hollow shaft with cable outlet, M12 or
M23 male connector (all dimensions in mm)
Operating temperature measuring point (freely selectable, around the
1
housing surface area in each case, approx. 3 mm away from flange)
Vibration measuring point (on the housing front face in each case,
2
approx. 3 mm away from edge of housing)
Keyway
3
2
1
3
Figure 2: Dimensional drawing of blind hollow shaft with cable outlet, M12 or
M23 male connector (all dimensions in mm)
Operating temperature measuring point (freely selectable, around the
1
housing surface area in each case, approx. 3 mm away from flange)
Vibration measuring point (on the housing front face in each case,
2
approx. 3 mm away from edge of housing)

10 Ordering information

Versions
S Singleturn
M Multiturn
S F 6 0
Table 4: Ordering code
Electrical interface
HIPERFACE
H
Shaft diameter
Metal, 8 mm
K
1 Metal, 3/8"
L Metal, 10 mm
M Metal, 12 mm
N Metal, 1/2"
R Metal, 14 mm
P Metal, 15 mm
Connection type
A Male connector M23, 12-pin, radial outlet
B M12 male connector, 8-pin, radial outlet
K Cable, 8-wire universal, 1.5 m
Mechanical interface
B Blind hollow shaft
T Through hollow shaft
Stator coupling
0
2
S - H
SFS60S/SFM60S | SICK
3
Standard version
Variant 2
Memory bank
K02 E²PROM 2048
K 0 2
9